Frigidaire FAHE4044MW0 Скачать руководство пользователя страница 15

Страница: 15 / 72

SECTION 2 - INSTALLATION INFORMATION

NOTE

A wiring diagram and technical data sheet are located

inside the washer console.

CAUTION

Failure to use accessories manufactured by (or approved

by) the manufacturer could result in personal injury,

property damage or damage to the washer.

WARNING

ELECTRICAL SHOCK HAZARD

Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

Replacement parts:

If replacements parts are needed for your washer,

contact the source where you purchased your washer or

refer to your

Use and Care Guide for more information.

To remove the console faceplate follow the directions

below:

1. Disconnect washer from electrical source.
2. Remove the hole plugs on the back of the console

housing.

3. Insert a small, straight blade screwdriver to gently pry

downward on each faceplate retaining tab.

4. Gently lay the console faceplate forward without

pulling wires to access technical/wiring diagram.

5. When fi nished with repair, return sheet inside console,

snap faceplate to console housing and reinstall hole

plugs.

MOBILE HOME INSTALLATION KIT

P/N 137067200

Installation in a mobile home requires the use of a

MOBILE HOME INSTALLATION KIT.

INLET HOSE KITS
Please call 866-233-8353 (in Canada, 800-265-8352)

to explore hose kit options that will meet your specifi c

installation needs.

UNIVERSAL APPLIANCE WRENCH

P/N 137019200

A UNIVERSAL APPLIANCE WRENCH is available to aid in

dryer/washer feet adjustment.

TOUCH UP PAINT PENS*

Classic White Touch Up Pen - P/N 5304468812

*Other colors may be available. Contact the source where you

purchased your washer.

Technical Sheet/Wiring Diagram:

TECH DATA SHEET/

WIRING DIAGRAM

2 - 9

Содержание FAHE4044MW0









































































Результаты поиска

Содержание FAHE4044MW0

Отзывы:

Frigidaire FAHE4044MW0, Обслуживание, Страница: 15 / 72

Результаты поиска

Содержание FAHE4044MW0

Отзывы: