background image

20

TROUBLESHOOTING GUIDE

TROUBLESHOOTING  

GUIDE 

Before calling for service, review this list. It may save you time and expense. This list includes 
common occurrences that are not the result of defective workmanship or materials in this 
appliance. 

PROBLEM CAUSE 

CORRECTION 

BEVERAGE CENTER OPERATION 

Beverage center does not 
run. 

 

Beverage center is plugged into a circuit 
that has a ground fault interrupt. 

 

Temperature control is in the “O” position. 

 

 

Beverage center may not be plugged in, 
or plug may be loose. 

 

House fuse is blown or circuit breaker 
tripped. 

 

Power outage. 

 

Use another circuit. If you are unsure about the 
outlet, have it checked by a certified technician. 

 

See 

SETTING THE TEMPERATURE CONTROL 

section. 

 

Ensure plug is tightly pushed into outlet. 

 

 

Check/replace fuse with a 15 amp time-delay 
fuse. Reset circuit breaker. 

 

Check house lights. Call local electric company. 

Beverage center runs too 
much or too long. 

 

Room or outside weather is hot.     

                  

 

Beverage center has recently been 
disconnected for a period of time. 

 

Doors are opened too frequently or too 
long. 

 

Beverage center door may be slightly 
open. 

 

Temperature control is set too low. 

 

 

Beverage center gasket is dirty, worn, 
cracked, or poorly fitted. 

 

It’s normal for the beverage center to work harder 
under these conditions. 

 

It takes 4 hours for the beverage center to cool 
down completely. 

 

Warm air entering the beverage center causes it 
to run more. Open door less often. 

 

See “

DOOR PROBLEMS” 

section. 

 

 

Adjust temperature control to a warmer setting. 
Allow several hours for temperature to stabilize. 

 

Clean or change gasket. Leaks in the gasket will 
cause beverage center to run longer in order to 
maintain desired temperature. 

Interior beverage center 
temperature is too cold. 

 

Temperature control is set too low. 

 

Adjust temperature control to a warmer setting. 
Allow several hours for temperature to stabilize. 

Interior beverage center 
temperature is too warm. 

 

Temperature control is set too warm. 

 
 

 

Door is kept open too long or is opened 
too frequently. 

 

Door may not be seating properly. 

 

Beverage center has recently been 
disconnected for a period of time. 

 

Adjust temperature control to a colder setting. 
Allow several hours for the temperature to 
stabilize. 

 

Warm air enters the beverage center every time 
the door is opened. Open the door less often. 

 

See “

DOOR PROBLEMS” 

section. 

 

It takes 4 hours for the beverage center to cool 
down completely. 

Beverage center external 
surface temperature is 
warm. 

 

The external walls can be as much as 30° 
F warmer than room temperature. 

 

This is normal while the compressor works to 
transfer heat from inside the beverage center. 

SOUND AND NOISE 

Louder sound levels 
whenever beverage center 
is on. 

 

Modern beverage centers have increased 
storage capacity and more stable 
temperatures. They require a high 
efficiency compressor. 

 

This is normal. When the surrounding noise level 
is low, you might hear the compressor running 
while it cools the interior. 

Longer sound levels when 
compressor comes on. 

 

Beverage center operates at high 
pressures during the start of the “ON” 
cycle. 

 

This is normal. Sound will level off or disappear as 
the beverage center continues to run. 

Fan runs when room 
temperature is below 45° F 

 

Exterior thermostat has activated the 
heater and fan. 

 

This is normal. 

Popping or cracking sound 
when compressor comes 
on. 

 

Metal parts undergo expansion and 
contraction, as in hot water pipes. 

 

This is normal. Sound will level off or disappear as 
beverage center continues to run. 

Bubbling or gurgling sound 
like water boiling. 

 

Refrigerant (used to cool beverage 
center) is circulating throughout the 
system. 

 

This is normal. 

 

Содержание Beverage Center II























Отзывы: