Frigidaire Affinity 6000 Series Скачать руководство пользователя страница 47

Страница: 47 / 74

Section 4 Component Teardown

4-5

Releasing The Bellows (Door Boot) From Front
Panel

The front of the bellows is installed over the lip of the
door opening in the front panel and held in place by a
spring loaded wire loop.

1. Open the loading door.
2. Using needle nose pliers, start where the spring and

wire are connected at the bottom of the bellows and

pull the wire out of the groove of the bellows.

(See Figure 4-15)

3. Pull the bellows off of the lip of the front panel.
(See

Figure

4-16)

Figure 4-15.

Figure 4-16.

Figure 4-17.

Figure 4-18.

Door Safety Switch Removal

1.   Disconnect the washer from the electrical supply.
2.   Release the bellows from the front panel.
3.   Remove the (2) screws securing the switch

assembly to the front panel. (See Figure 4-17)

4. Pull the switch assembly into the door opening and

unplug the electrical connectors. (See Figure 4-18)

Lip Of Front

Panel

Screws

Electrical

Connections

Содержание Affinity 6000 Series











































































Результаты поиска

Содержание Affinity 6000 Series

Отзывы:

Frigidaire Affinity 6000 Series, Руководство по обслуживанию, Страница: 47 / 74

Результаты поиска

Содержание Affinity 6000 Series

Отзывы: