Frigidaire Affinity 6000 Series Скачать руководство пользователя страница 44

Страница: 44 / 74

Section 4 Component Teardown

4-2

This section will describe how to access and remove
serviceable components from the washer. Unless stated,
the procedure will be the same on all models. Unless
stated, reverse the procedure to reinstall the component.

Door Strike Removal

1. Open the loading door and extract the (2) screws

holding the strike to the inner door liner.

(See Figure 4-1)

Loading Door Removal

1. Extract the (3) screws securing the door hinge to

the front panel. (See Figure 4-2)

2. Lift up and out on the door to disengage the hook

on the hinge from the slot in the front panel.

(See Figure 4-3)

Figure. 4-1.

Figure 4-2.

Figure 4-3.

Screws

Figure 4-4.

Loading Door Breakdown

1. Remove the loading door from the washer and place

it on a soft flat surface.

2. Remove the door strike and the (8) screws holding

the inner liner to the outer liner and lift the inner
liner off. (See Figure 4-4) (continued next page)

Screws

Содержание Affinity 6000 Series











































































Результаты поиска

Содержание Affinity 6000 Series

Отзывы:

Frigidaire Affinity 6000 Series, Руководство по обслуживанию, Страница: 44 / 74

Результаты поиска

Содержание Affinity 6000 Series

Отзывы: