manualshive.com logo in svg

Frigidaire Affinity 6000 Series, Руководство по обслуживанию, Страница: 26 / 74

Поделиться
Скачать
Frigidaire Affinity 6000 Series Скачать руководство пользователя страница 26

  Section 2 Installation Information 

2-8

Washer and Dryer 15” Drawer Pedestal 
Installation

The Affinity Series washers and dryers use the same 
pedestal. 
Tools needed: 
 Level
 

9/16” open end wrench 

 

#2 Phillips screwdriver

 

Washer/Dryer Installation Kit

Pedestal Installation

1.  Attach the rear brackets to the pedestal with 
 

(4)- #10 screws (2 per bracket). (See Figure 2-9)

 
2.  Attach the front brackets and spacer plates to the 

pedestal with (4)- #10 screws (2 per bracket).

3.  Tilting the dryer back slightly to engage the slots in 

the rear of the dryer with the tabs of the rear 

 

brackets on the pedestal.

 

4.  Using two or more people, carefully lift the washer
 

onto the pedestal, tilting the washer back slightly to

 

align the holes in the rear of the washer with the 
slots of the rear brackets on the pedestals. 

Foam

Rear Bracket

Rear Bracket

Screws

Screws

Screws

Front Bracket

Front Bracket

Pedestal Top

Do not remove the foam in the middle of the pedestal. 
It reduces vibration noise.

NOTE 

This kit is intended to be installed by persons having 
electrical and mechanical training and a level of
knowledge considered acceptable in the appliance 
repair trade.

NOTE 

Figure 2-9.

2 – Spacer Plates (Washer)

2 - Rear Brackets (Washer)

14 - #10 x 1/2" Screws

(Washer / Dryer)

2 - Front Brackets

(Washer / Dryer)

2 - Rear Brackets (Dryer)

If washer was previously installed, disconnect power 
cord, remove the inlet hoses from the water faucets 
and tape the drain hose to the top of the washer to 
eliminate excess water on the floor.

NOTE 

If the mounting holes do not align, make sure washer 
leveling legs are adjusted fully into washing machine. 
Turn each leg tight to the base.

NOTE 

Figure 2-10.  Kit Components

Содержание Affinity 6000 Series











































































Отзывы:

Нет отзывов