background image

1 MOUNTING 

SPACE

This Microwave Oven/Hood requires a mounting space on 
a wall as shown in Figure 1. It is designed to be used with 
standard 12" wall cabinets.

TINSEB151WRRZ

Printed in Thailand

Backsplash

Figure 1

15.5"

30" or more 

from cooking 

surface

30"

At least 2"

12"

P/N 316137234

NEED HELP?

For customers in the United States, call: 1-800-944-9044 

For customers in Canada, call: 1-800-213-9397 (English)  
 

 

          1-800-668-4606 ext.8199 (French)

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

BEFORE YOU BEGIN

  

          

• 

IMPORTANT

 Save these instructions for local 

inspector’s use.

• 

IMPORTANT

 Observe all governing codes and 

coordinates.

• 

NOTE TO INSTALLER

 – Be sure to leave these 

instructions with the Consumer. 

• 

NOTE TO CONSUMER

 

– Keep these instructions for 

future reference.

• 

SKILL LEVEL

 – Installation of this appliance requires 

basic mechanical and electrical skills.

•  Proper installation is the responsibility of the installer.

•  Product failure due to improper installation is not covered 

under the Warranty.

•  Please read all instructions thoroughly before installing 

the Over the Range Microwave Oven. Two people are 
recommended to install this product.

•  If a new electrical outlet is required, its installation should be 

completed by a quali

fi

 ed electrician before the Microwave 

Oven  is  installed.  See 

3 ELECTRICAL GROUNDING 

INSTRUCTIONS

 on page 2.

Read these instructions completely and carefully.

INSTALLATION  INSTRUCTIONS

Over The Range Microwave Oven

2 WALL 

CONSTRUCTION

This Microwave Oven/Hood should be mounted against and 
supported by a 

fl

 at vertical wall. The wall must be 

fl

 at  for 

proper installation. If the wall is not 

fl

 at, use spacers to 

fi

 ll in 

the gaps. Wall construction should be a minimum of 2" x 4" 
wood studding and 

³⁄₈

" or more thick dry wall or plaster/lath. 

The mounting surfaces must be capable of supporting weight 
of 110 pounds—the oven and contents—AND the weight of 
all items which would normally be stored in the top cabinet 
above the unit.

The unit should be attached to a minimum of one 2" x 4" 
wall stud or two 2" x 3" wall studs.

To 

fi

 nd the location of the studs, one of the following methods 

may be used:

A.  Use a stud finder, a magnetic device which locates the 

nails in the stud.

B.  Use a hammer to tap lightly across the mounting surface 

to find a solid sound. This will indicate stud location. 

The center of the stud can be located by probing the wall with 
a small nail to 

fi

 nd the edges of the stud and then placing a 

mark halfway between the edges. The center of any adjacent 
studs will normally be 16" or 24" to either side of this mark.

66" or more 

from floor

Содержание 316137234









Отзывы: