Frick Vyper 572 Скачать руководство пользователя страница 68

Страница: 68 / 76

VYPER

™

VARIABLE SPEED DRIVE

MAINTENANCE

100-210 IOM (

JUL

09)

Page 68

Fault 82: Interface Board Motor Current Limit Override

(Warning Only)

Message

Quantum: “Fault 82”

Quantum LX: Interface Board Motor Current Limit Override

(Warning Only)

This warning is triggered whenever the Frick Interface Board

is operating under Current Limit Override. If the Run Com-

mand signal is disengaged, any current limit in effect will be

cancelled. If the Run Command signal is engaged, the actual

speed command is set to the initial speed command and the

Motor Current is monitored every two seconds. If the Motor

Current rises above 103%, the unit enters current limit and a

warning condition will be set. Thereafter, as long as the Motor

Current stays above 100%, the actual speed command will

be reduced by 6 RPM every two seconds.

Once the Motor Current falls below 100%, the actual speed

command is increased by 6 RPM every two seconds, until

the actual speed command falls within ± 6 RPM of the initial

speed command, when speed returns to the initial speed

command, the warning is cleared. The actual speed com-

mand is used to set the Quantum

™

LX Vyper

™

operating

speed.

Fault 83: Harmonic Filter Serial Communication

(Warning Only)

Message

Quantum: “Fault 83”

Quantum LX: “Harmonic Filter Serial Communication (Warn-

ing Only)”

When requesting Status data, the response data from the

Harmonic Filter includes a bit that indicates whether com-

munications were lost from the Vyper

™

to the Harmonic Filter.

If this bit is high for twenty consecutive seconds, this warning

is triggered. This warning is also triggered whenever a twenty-

second receive, timeout, or checksum fault is detected on

the Harmonic Filter communications.

This message can also occur as a background message

when the chiller is running. When this message is displayed,

all filter related values are unavailable. If communication is

reestablished, the message will disappear and normal values

will again be displayed. If this problem is encountered, the

ribbon cable connecting the Vyper

™

Logic board to the Filter

logic board should be checked.

Fault 84: Harmonic Filter Input Frequency Out of Range

(Warning Only)

Message

Quantum: “Fault 84”

Quantum LX: “Harmonic Input Frequency Out of Range

(Warning Only)”

The power line frequency detected by the Vyper harmonic
filter is outside the range of 58 to 62 Hz (60 Hz), or 49 to
51 Hz (50 Hz) and the Quantum

™

LX panel displays Fault 84.

This message automatically clears when the line frequency
is within range.

Содержание Vyper 572













































































Результаты поиска

Содержание Vyper 572

Отзывы:

Бренды по названию

Популярные бренды

Frick Vyper 572, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание Vyper 572

Отзывы:

Бренды по названию

Популярные бренды