FRIATEC FRIALEN Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 32

background image

8

Scraper Tool

Estimated swarf thickness (mm)

Abrasion limit (mm)

FWSG 225

0.25 - 0.35

0.4

FWSG 710

0.30 - 0.40

0.5

FWSG SE 250 - 315

0.25 - 0.35

0.4

WARNING!
If the oxide layer is not removed completely, inhomogeneous, leaking
fusion joints may result.

WARNING!
The FWSG 710 scraper tool must in all circumstances be used for fittings
from d 710.

A one-time, complete removal is sufficient (min. 0.15 mm).

Damages to the pipe surface as e.g. axial grooves or scratches may not be
located within the fusion zone.

WARNING!
An excessive swarf removal may result in an excessively large annular
gap which either cannot or only insufficiently closed by fusion (for the
remedy see item 4.8).

Please thus regularly check the condition of the blade at the manual
scraper and the wear of the scraper blade at the scraper tool. Worn blades
must be replaced (see FRIALEN

®

Info No. 1).

Please note that the indicated wearing margin applies to FRIALEN

®

Safety Fittings. Where appropriate please observe manufacturers’
indications.

Filing or sanding are not permitted because contaminations are
introduced.

For a control of the complete surface removal over the entire surface, we
recommend to apply marking (control) lines (see Figure 3). If during scraping of
the surface non-scraped areas occur at some points (e.g. in case of oval pipes),
these areas are to be reworked.

FL_2104_8_GB_II_08.p65

25.03.2008, 9:48 Uhr

8

«
...
6
7
8
9
10
...
»

Содержание FRIALEN

































Отзывы:

Нет отзывов

Похожие инструкции для FRIALEN

Бренд: Oemtools Страницы: 4

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: NEC Страницы: 29

Бренд: 3M Страницы: 48

Бренд: 3M Страницы: 19

Speedglas G5-01

Бренд: 3M Страницы: 62

Quickfit Nexus Exit

Бренд: Thomas & Betts Страницы: 2

Бренд: Raymarine Страницы: 24

Бренд: Hansen Страницы: 72

Бренд: AAT Страницы: 16

Бренд: AAT Страницы: 40

Platinum Series

Бренд: Dairy Tech Страницы: 38

Бренд: H&S Страницы: 34

Бренд: QAL Medical Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды