manualshive.com logo in svg

Fri-Jado Cold MCC, Руководство по обслуживанию, Страница: 15 / 147

Поделиться
Скачать
Fri-Jado Cold MCC Скачать руководство пользователя страница 15

 Rev 3 Service Manual MCC Hot / Cold 2021

Page 15 

4.0

 Installation

 

Adjusting the hight of the doors

 

To adjust the doors in height after placement, 

 

Loose the mounting screws of the hinge a little.

 

If loose, the glass can be moved slightly inside 

 

the hinge assembly

4.10  Installation and positioning

  

 

WARNING 

  

 

 

Cold units: The propane refrigerant is highly flammable.  

 

 

All safety precautions must be followed.

  

 

WARNING 

  

 

 

Position the unit on a flat and horizontal surface.     

 

 

 

 

 

 

 

A  

temporally inclined plane of maximum  5° is allowed.

 

 

• 

Place the unit level on a sufficiently sturdy floor.  

  

 

 

• 

Keep the weight of the unit in mind.    

 

 

  

 

 

• 

Use a level-ling instrument to level the unit by adjusting the unit’s legs.

 

 

 

(Refer to next page)

 

 

• 

MCC cold: Please take notice of label with minimum space required

 

 

• 

Be sure that the personnel have sufficient room to work with the unit.

 

 

• 

Keep a distance of at least 150 mm (6 inch) between the back wall and the unit.

 

 

• 

Do not position a unit near a doorway, a ventilation device or a refrigerator in order  

 

 

 

 

to avoid any negative effects on the unit’s operation by a cold airflow.  

   

   

The unit is designed for a maximum draft of 0.2 m/s (0.65 ft./sec).

 

 

• 

Do not place the unit into direct sunlight.

 

 

• 

Be sure that the ambient temperature for cold models remains between 

 

 

 

10 ºC - 25 ºC (50 ºF - 77 ºF) and that the relative air humidity remains below 60%.  

 

 

 

Cold units have been designed to operate at climate class 3 (according ISO 23953).  

   

 

 

• 

Hot units should not be used below 20 ºC (68 ºF) ambient temperatures.

 

 

• 

Keep the plinth free from any obstacles to ensure ventilation.

  

Содержание Cold MCC




















































































































































Отзывы:

Нет отзывов