Fresenius Medical Care 460018 Скачать руководство пользователя страница 9

Страница: 9 / 75

P/N 460018 Rev. D

ECTION

PECIFICATIONS AND

-I

NSTALLATION

EQUIREMENTS

Prior to operating the Fresenius Medical Care Dry Acid Dissolution Unit: 132 Gallons (500 Liters),

adequate power and water connections must be made. The Dry Acid Dissolution Unit should be installed

in an appropriate environment (indoors) free from extremes of temperature and humidity, free of the

presence of flammable anesthetics, reasonably protected from dust and dirt contamination, liquid

splashes, bright sunlight or high intensity lighting.

The Fresenius Medical Care Dry Acid Dissolution Unit: 132 Gallons (500 Liters) is in compliance with the

electrical requirements of

ISO 13958:2009 (E) / IEC 60601-1

Failure to install the Dry Acid Dissolution Unit according to these guidelines may result in improper

operation or early failure of the device or its components. Direct sunlight or high intensity lighting may

interfere with the proper operation of the optical sensors. Direct sunlight may cause discoloration of the

polypropylene tank, lid or electronic housing.

The Dry Acid Dissolution Unit needs to be set up using the following parameters:

A 15 amp

GFI

duplex outlet is required. The Dry Acid Dissolution Unit requires 120 VAC, 60 Hz,

single phase power. The Dry Acid Dissolution Unit uses approximately 7.3 amperes total. Electrical

service should meet all applicable national, state and local code requirements.

The electrical power cord, input water hose, and output drain hose shall be properly routed away

from high traffic areas and installed in such a way that does not cause any electrical or safety

hazards.

The treated water source must meet

ANSI/AAMI

ISO

requirements for water for hemodialysis,

currently

ANSI/AAMI RD62

, or

ISO 13959

. Plumbing service must meet all national, state and local

plumbing codes. The Dry Acid Dissolution Unit uses approximately 132 gallons (500 liters) of water

per batch of product.

WARNING!

DO NOT PERMANENTLY INSTALL

RANSFER

OSE TO A STORAGE TANK

CONTAINER

Supply water treatment system should be capable of a minimum flow rate of ½ gallon per minute.

The maximum input water pressure is 60 psi.

The water temperature should be 20°-30°C (68°-86°F) for proper dissolution mixing conditions.

Height from floor to top of motor is 60 inches.

Platform for the Dry Acid Dissolution Unit is 55 inches long by 36 inches wide.

Transfer filter housing is equipped with a ¾” hose barb fitting.

There is a ¾” hose barb inlet fitting, and another for the drain outlet.

10.

Dry Acid Dissolution Unit must be level.

11.

Dry Acid Dissolution Unit weight is 395 lbs. empty and 1,775 lbs. filled.



CAUTION!

HE FLOOR MUST BE CAPABLE OF WITHSTANDING THE MAXIMUM WEIGHT OF

1,775

POUNDS

A floor drain emptying into a sewer line must be in the immediate area of the Dry Acid Dissolution

Unit.

NOTE:

CID

ISSOLUTION

NIT

’

ANK IS MADE OF NON

FERROUS MATERIAL AND ALL METAL

SURFACES ARE GROUNDED

Содержание 460018












































































Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care 460018, Руководство оператора

Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды