Fresenius Medical Care 460018 Скачать руководство пользователя страница 31

Страница: 31 / 75

M A I N T E N A N C E

C o n t i n u e d

P/N 460018 Rev. D

Checking bleach residuals during DRAIN Operation from the drain hose.

•

Have chlorine test strip ready for use.

•

Using STEP button step to the DRAIN Operation.

•

Press the RINSE CYCLE side START button.

•

PAUSE Indicator Light will turn off and the Drain Valve will OPEN. Allow water to drain for 30 seconds.

•

Place test strip under the flow for 30 seconds or the recommended time on the test strip

manufacture’s instruction. Press PAUSE button once you are complete with this step.

•

Ensure that you check the results of the test strip immediately.

If residual bleach levels are higher than ANSI/AAMI Standard limit of <0.1 ppm (RD61: 2006), in any of the

two testing regions initiate another complete RINSE CYCLE. After the RINSE CYCLE is complete, start from

section 8.3, #5, to check for residual bleach. Continue the RINSE CYCLE and test procedure until bleach

residuals are within ANSI/AAMI Standard limit of <0.1 ppm (RD61:2006) at the end of the Transfer and

Drain Hose.

Once you have attained an acceptable bleach residual reading, ensure the Mixing Tank is empty, power to

the Dry Acid Dissolution Unit has been turned off and CLOSE the Main Transfer Ball Valve near the filter

housing. Then, connect the Transfer Hose back onto the Dry Acid Dissolution Unit Transfer Hose Holder

(See Diagram 2: Dry Acid Dissolution Unit, page 8).

10.

Remove Filter Housing and drain all residual water from the Housing. Install new Filter and tighten Filter

Housing into place (Figure 21).

Figure 21

11.

Immediately after RINSE CYCLE, make a batch of Dry Acid Product using Section 7, page 14. Leaving the

Dry Acid Dissolution with only treated water or wetted with only treated water leaves the Unit

susceptible to bacterial growth.

8.4

ILTER

AINTENANCE

The 1-micron filter should be changed under the following conditions:

1. The Filter should be changed after mixing 6 batches.

2. When the Dry Acid Dissolution Unit requires disinfection.



CAUTION!

O NOT ALLOW THE

NIT TO REMAIN FULL OF WATER WITHOUT THE ADDITION OF

RESENIUS

EDICAL

ARE

CID

RODUCT

ACTERIAL GROWTH MAY OCCUR

A. Remove filter housing

B. Insert filter (P/N G84-

202-12)

C. Install filter housing onto

the filter holder.

D. Tighten the filter housing

Содержание 460018












































































Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care 460018, Руководство оператора

Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды