Fresenius Medical Care 460018 Скачать руководство пользователя страница 28

Страница: 28 / 75

7 . 3 T R A N S F E R T O I N D I V I D U A L C O N T A I N E R S

P/N 460018 Rev. D

7.3

RANSFER

NDIVIDUAL

ONTAINER

To transfer product into individual containers (containers must be properly labeled):

Connect the Transfer Hose to

the Transfer Nozzle.

Place the Transfer Nozzle into

the opening of an individual

container.

Slightly OPEN the Main Transfer

Ball Valve on the top of the

Filter Housing.

With the Transfer Light flashing,

Press Dissolution START button.

The Transfer Pump will start.

Slowly OPEN Ball Valve on the

Transfer Nozzle until the desired

rate of flow through the nozzle

is achieved.

Once the manual TRANSFER Operation has been completed

and the individual containers are filled, CLOSE Transfer Nozzle

Valve. Press the PAUSE button.

When the Dry Acid Dissolution Unit is empty, the Dry Acid

Dissolution Unit will step to the CYCLE COMPLETE Operation.

CLOSE the Dry Acid Dissolution Unit’s Main Transfer Ball

Valve. Then Remove Transfer Nozzle and place Transfer Hose

onto the Transfer Hose Holder of the Tank. Ensure you place

the Transfer Nozzle in appropriate area free from dirt and

other contaminates.



CAUTION!

F THE PUMP IS RUN DRY FOR LONGER THAN

SECONDS THIS MAY CAUSE

UMP FAILURE

NOTE:

CID CONCENTRATE SHOULD NOT BE STORED IN MIX TANK LONGER THAN

DAYS FROM THE DATE OF MIXING

CID CONCENTRATE MAY BE STORED FOR LONGER PERIODS IN APPROVED CONTAINERS UNDER PROPER STORAGE

CONDITIONS

-Connect

Transfer Line to
Transfer Nozzle

– Open

Main Transfer
Ball Valve

– Press

Dissolution
START button

–

Transfer Nozzle

Transfer Line

– Slowly

Open to
desired rate

Содержание 460018












































































Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care 460018, Руководство оператора

Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды