background image

P5F111 User’s Manual

1

 

Copyright Notice

The information contained in the user’s manual and all accompa-
nying documentation is copyrighted and all rights are reserved. 
This publication may not, in whole or in part, be reproduced, 
transcribed, stored in a retrieval system, translated into any lan-
guage or computer language, or transmitted in any form whatso-
ever without the prior written consent from the manufacturer, 
except for copies retained by the purchasers for their personal 
archival purposes. 

The manufacturer reserves the right to revise this user’s manual 
and all accompanying documentation and to make changes in the 
content without obligation to notify any person or organization of 
the revision or change.

IN NO EVENT WILL THE VENDOR BE LIABLE FOR 
DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGES ARISING OUT OF THE USE OR 
INABILITY TO USE THIS PRODUCT OR DOCUMENTA-
TION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT 
HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, 
OR DATA STORED OR USED WITH THE PRODUCT, 
INCLUDING THE COSTS OF REPAIRING, REPLACING, OR 
RECOVERING SUCH HARDWARE, SOFTWARE, OR 
DATA.

All trademarks mentioned in this document are acknowledged.

The Specification on the manual is subject to change without 
notice.

 Copyright 1999.

Содержание P5F111


























































Отзывы: