is a one time only reminder alarm.
Press and hold Light/Set b u t t o n LT
for approximately three seconds to
enter alarm setting mode. The min-
utes digit will flash. Press S t a r t / S t o p
b u t t o n RT to advance the flashing
minutes digit.
Press Mode button LB to advance
tens of minutes. Press Start/Stop
button RT to advance the flashing
tens of minutes digit.
Press mode button L B to advance the
hours digit. P r e s s Start/Stop b u t t o n
R T to advance the flashing hours
digit. While setting the flashing hours
digit, “A” or “P” is displayed next to
alarm. “A” designates a.m. and “P”
designates p.m.
Press Light/Set button LT to exit
the alarm setting mode. To activate
the alarm while in alarm mode:
Press Start/Stop button RT to
activate the alarm ( (•) ) and/or
hourly chime .
Note the setting sequence is: alarm
on, chime on, both alarms on, both
alarms andchime off.
Again, press Lap/Reset button RB
to toggle between alarm 1 and
alarm 2. Alarm 2 is set and
activated the same way as alarm 1.
A1 ((•)) = alarm 1 set.
A2 ((•)) = alarm 2 set.
A1 A2 ((•)) = alarm 1 & 2 set.
= hourly chime on.
HOW TO OPERATE THE
COUNTDOWN TIMER
Press Mode button LB three times
from the normal time mode to enter
the countdown timer mode. Normal
time will remain in the lower row
and the timer will appear on the
789 SHARK™
INSTRUCTIONS
FEATURES:
• CURRENTTIME (HR., MIN.,
& SEC.)
• DAY / M O N T H / D AT E
• CHRONOGRAPH WITH SPLIT
& LAP T I M E S
• DUALALARMS ( 1 DAILY
R E P E ATING, 1 NON-
R E P E ATING REMINDER.)
• COUNTDOWN, COUNTDOWN
R E P E AT, COUNTDOWN
CHRONO
L A P & COUNTDOWN CHRONO
S P L I TT I M E R S
• DUAL T I M E
• HOURLY C H I M E
• OPTIONAL24-HR. TIME
( M I L I TA RYTIME. )
• WATER RESISTA N T TO
300 FT.
• NIGHT V I S I O N
™
E L E C T R O -
L U M I N E S C E N T
B A C K L I G H T I N G
NORMAL TIME MODE
( The term “Mode” means the func-
tion status of the watch.) N o r m a l
time mode shows hours, minutes,
seconds, day and date. To set time,
see operating instructions on How
to Set Normal Time.
NORMAL TIME MODE
KEY TO SYMBOLS
LT - Left Top (Light/Set)
LB - Left Bottom (Mode)
RT - Right Top (Start/Stop)
RB - Right Bottom (Lap/Reset)
HOW TO SETNORMAL TIME,
DATE AND 24-HOUR FORMAT
Note: While in the setting mode,
the Night Vision
™
backlight will
remain illuminated. If no buttons
are pressed for approximately ten
seconds, the watch will exit the
setting mode.
From Normal Time mode, press
and hold the light/set button LT for
approximately three seconds; the
seconds digits will flash. Pressing
the Start/Stop button RT will reset
the seconds digits to 0. If seconds
are greater than 30, one will be
added to the minutes digit.
To set minutes, press M o d e b u t t o n
L B; single minutes digit will flash. To
advance flashing minutes digit, press
Start/Stop b u t t o n R T;hold for
r a p i d
advance.
To set tens of minutes, press M o d e
b u t t o n LB; tens of minutes will flash.
To advance flashing tens of minutes
press Start/Stop button R T; hold for
rapid advance.
Continuing through the setting
mode, the setting sequence is a
continuous loop of: seconds • single
minutes • tens of minutes • hours •
day/month/date • 12/24-hour mode,
and looping back to seconds. When
setting is complete, press Light/Set
button LT to return to normal time
mode.
HOW TO OPERATE
CHRONOGRAPH/STOPWATCH
The chronograph will record a
maximum of 99 hours, 59 minutes
and 59 seconds. Press Mode
button LB once from normal time
mode to enter the chronograph
mode. Normal time will remain on
the lower row, chronograph on the
upper row. “CH” flag will be d i s p l a y e d .
Reset the chronograph to zero by
pressing Lap/Reset button RB.
Press the Light/Set button LT to
switch between Lap and Split
mode.
(“LAP” flag will be displayed for lap
mode and “SPL” flag will be
displayed for split time mode.)
Split time is the time elapsed since
the start of the chronograph. To use
the split time feature, “SPL” flag
must be displayed. Press
Start/Stop button RT to start
chronograph. “SPL” flag will begin
flashing. Press Lap/Reset button
RB to view split time. Chronograph
will continue to count while split
time is displayed. To release split
time and return to running chrono-
graph, press Lap/Reset button RB.
Each press of Lap/Reset button RB
will display a split time.
To stop chronograph, press S t a r t / S t o p
button R T. Reset the chronograph to
zero by pressing the Lap/Reset b u t t o n
R B . Lap time is the time elapsed since
the previous lap. To use the lap time
feature, “LAP” flag must be displayed.
Reset the chronograph to zero by
pressing the Lap/Reset button R B .
Enter LAPmode by pressing L i g h t / S e t
button LT. Press Start/Stop button R T
to start chronograph. “LAP” flag will
begin flashing. Press Lap/Rest b u t t o n
RB to view lap time. Chronograph will
start counting next lap while lap time is
displayed. To release lap time and
return to running chrono, press
Lap/Reset button RB. Each press of
Lap/Reset button RB will display a lap
t i m e .
To stop chronograph, press
Start/Stop button RT. Reset the
chronograph to zero by pressing
the Lap/Reset button RB.
HOW TO SET AND OPERAT E THE
ALARMS AND HOURLY CHIME
From normal time mode, press
Mode button LB twice to enter the
alarm mode. Normal time remains
on the lower row, alarm time on the
upper row. Pressing Lap/Reset but-
ton RB will toggle between alarm 1,
indicated by “A1” flag, and alarm 2,
indicated by “A2” flag. Alarm 1 is a
daily, repeating alarm,and alarm 2
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
LT
RT
LB
RB
continued...
