Freescale Semiconductor MSC8144E Скачать руководство пользователя страница 451 | Manualshive

Страница: 451 / 1374

background image

L2 ICache Programming Limitations

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

11-37

11.9

L2 ICache Programming Limitations

The L2 ICache programming has the following limitations:

Register access width is restricted to the actual register width. Register access attempts
with an incorrect access width may cause data corruption.

Accesses to debug-related registers: L2IC_DBGACS, L2IC_DBGDATA, L2IC_TAG,
L2IC_LRM and L2IC_VALID have meaning in Cache Debug mode only.

Initiation of sweep command by writing to L2IC_CR1, should be done according to the
routine that is described in Section 11.4.6.6.

To configure each of the L2 ICache CLASS registers, please refer to Section 11.8.9 to
Section 11.8.11.

To configure the TL1IC in each of the two L2IC_Bs use the MBus interface to the L2RB
(register file block of the L2 ICache).

Every access to L2 ICache should start and end in the same cache line so the CLASS can
handle the interleave between the L2 instruction cache banks.

Accesses from the DSP core subsystem toward memory through the L2 ICache must be of
one VBR or with a burst of 4 VBRs (byte count of 64). You must program this limitation
into the MMU in the DSP core subsystem to ensure this operation.

Accesses from the DSP core subsystem ICache toward memory via the non-cacheable
route through the L2 ICache are restricted to a burst size of 1 beat or 4 beats (2-beat or
8-beat accesses are not permitted).

Accesses from the DSP core subsystem DCache toward memory are restricted to a burst
size of 1 beat or 4 beats (2-beat or 8-beat accesses are not permitted).

L2 ICache does not support nested sweeps. Avoid it by using a dedicated semaphore and
polling the relevant L2 ICache Control Register bit (see Section 11.8.2).

ECC is not supported during debug mode and to L2 ICache addresses written during
debug.

«
...
449
450
451
452
453
...
»

Содержание MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8144E

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 5

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

Бренд: Clavister Страницы: 89

FRDM-STBC-SA9500

Бренд: Freescale Semiconductor Страницы: 2

Бренд: Dialogic Страницы: 2

Бренд: HARTING Страницы: 13

Бренд: axing Страницы: 52

Бренд: Renesas Страницы: 76

Бренд: Aaeon Страницы: 57

Бренд: Juniper Страницы: 196

Бренд: Alcatel-Lucent Страницы: 60

CL-SOM-AM57 Series

Бренд: CompuLab Страницы: 79

Бренд: Renesas Страницы: 40

Бренд: FOR-A Страницы: 37

Бренд: ADLINK Technology Страницы: 86

EcoJet EcoStar 1500

Бренд: Ecolab Страницы: 80

Бренд: ICP DAS USA Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды