Freescale Semiconductor MSC8144E Скачать руководство пользователя страница 1054 | Manualshive

Страница: 1054 / 1374

background image

MSC8144E Reference Manual, Rev. 3

21-12

Freescale

Semiconductor

Timers

21.1.5.3

Broadcast from an Initiator Timer

Any timer can be assigned as an initiator. An initiator compares signal can be broadcast to the
other timers within the module. The other timers can be configured as follows to reinitialize their
timers and/or force their output to predetermined values when an initiator timer compare event
occurs:

Select one timer as the initiator timer by setting the TMRxSCTL[MSTR] bit.

Program the other timers to perform an action when a compare event occurs on the
initiator timer as follows:

— The other timer is reinitialized if its TMRxCTL[EIN] bit is set.
— The other timer forces its output flag signal if its TMRxSCTL[EEOF] bit is set.

21.1.6 Resets and Interrupts

The timers reset conditions are shown in Chapter 5, Reset. This reset forces all registers to their
reset state and clears the output flag signal if it is asserted. The timer is turned off until the
settings in the control register are changed. Each timer in a quad timer module can be
programmed for interrupts. The available types of interrupts are as follows:

Timer compare

Timer compare 1

Timer compare 2

Timer overflow

Timer input edge

Each of these different types is ORed together within each timer to generate a single interrupt
request signal to the interrupt controller.

21.1.6.1

Timer Compare Interrupts

Interrupt requests are generated when a successful compare occurs between a timer and its
compare registers while the Timer Compare Flag Interrupt Enable bit, TMRxSCTL[TCFIE], is
set. These interrupt requests are cleared by writing a zero to the appropriate TMRxSCTL[TCF]
bit. When a timer compare interrupt is set in the TMRxSCTL and the compare preload registers
are available, one of the following two interrupts is also asserted:

Timer compare 1 interrupt

Timer compare 2 interrupt

Timer compare 1 interrupts are generated when a successful compare occurs between a timer and
its TMRxCMP1 register while the Timer Compare 1 Interrupt Enable (TCF1EN) is set in the
TMRxCOMSC register. These interrupts are cleared by writing a zero to the
TMRxCOMSC[TCF1] bit. Timer compare 2 interrupts are generated when a successful compare

«
...
1052
1053
1054
1055
1056
...
»

Содержание MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8144E

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

EXPANSION CARD X-DANTE

Бренд: Behringer Страницы: 65

Бренд: Alesis Страницы: 61

Бренд: Cypress Semiconductor Страницы: 10

Бренд: Baicells Страницы: 10

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: SurfControl Страницы: 2

500 - DATASHEET REV 003

Бренд: Intel Страницы: 67

Бренд: EZCast Pro Страницы: 4

Бренд: ekwb Страницы: 2

Бренд: Digital Voice Systems Страницы: 32

Бренд: Digital Audio Corporation Страницы: 164

Бренд: JETWAY Страницы: 63

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

X-NUCLEO-AMICAM1

Бренд: ST Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды