manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Руководство пользователя

Поделиться
Скачать
Freescale Semiconductor MPC5632M Скачать руководство пользователя страница 426

MPC563XM Reference Manual, Rev. 1

426

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

14.6.1.1

Peripheral Interrupt Requests

An interrupt event in a peripheral’s hardware sets a flag bit which resides in that peripheral. The interrupt 
request from the peripheral is driven by that flag bit. While the INTC can support up to 504 peripheral 
interrupt requests, the actual number is dependent on the SoC implementation.

The time from when the peripheral starts to drive its peripheral interrupt request to the INTC to the time 
that the INTC starts to drive the interrupt request to the processor is three clocks.

Interrupt requests from devices external to the SoC are classified as peripheral interrupt requests in this 
block guide. An anticipated way that an SoC will support an external interrupt request is by having a flag 
bit in a peripheral on the SoC which records an edge on the external interrupt request. This flag bit then 
drives a peripheral interrupt request. If the external interrupt request is level sensitive instead of edge 
triggered, the flag bit is effectively on the external device and not on the SoC. In that case, the external 
interrupt request must have transitioned as a result of clearing the flag bit on the external device before 
either the INTC_EOIR_PRC0 or INTC_EOIR_PRC1 can be written.

14.6.1.2

Software Setable Interrupt Requests

An interrupt request is triggered by software by writing a ‘1’ to a SET

x

 bit in 

Section 14.5.10, “INTC 

Software Set/Clear Interrupt Registers (INTC_SSCIR0_3 - INTC_SSCIR4_7)

”. This write sets the 

corresponding CLR

x

 bit, which is a flag bit, resulting in the interrupt request. The interrupt request is 

cleared by writing a ‘1’ to the CLR

x

 bit.

The time from the write to the SET

x

 bit to the time that the INTC starts to drive the interrupt request to the 

processor is four clocks.

14.6.1.3

Unique Vector for Each Interrupt Request Source

Each peripheral and software setable interrupt request is assigned a hardwired unique 9-bit vector. 
Software setable interrupts 0 - 7 are assigned vectors 0 - 7 respectively. The peripheral interrupt requests 
are assigned vectors 8 to as high as needed to cover all of the peripheral interrupt requests. While the 
peripheral interrupt request input ports at the boundary of the INTC block are assigned specific hardwired 
vectors within the INTC, those input ports are not associated with any specific peripheral until the SoC 
integration. Those assignments are dependent on the SoC integration. Refer to the SoC guide for the 
assignments.

14.6.2

Priority Management

The asserted interrupt requests are compared to each other based on their PRI

x

 and PRC_SELx values set 

in 

Section 14.5.11, “INTC Priority Select Registers (INTC_PSR0_3 - INTC_PSR508_511)

”. The result of 

that comparison also is compared to PRI in the associated 

Section 14.5.4, “INTC Current Priority Register 

for Processor 0 (INTC_CPR_PRC0)

” or 

Section 14.5.5, “INTC Current Priority Register for Processor 1 

(INTC_CPR_PRC1)

”. The results of those comparisons are used to manage the priority of the ISR being 

executed by the associated processor. The associated LIFO also assists in managing that priority.

Содержание MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды