manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Руководство пользователя

Поделиться
Скачать
Freescale Semiconductor MPC5632M Скачать руководство пользователя страница 35

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

35

 

Preliminary—Subject to Change Without Notice

— Censorship disable register. By writing the 64-bit serial boot password to this register, 

Censorship may be disabled till the next reset

— A TAP controller state machine that controls the operation of the data registers, instruction 

register and associated circuitry

•

On-chip Voltage Regulator for single 5 V supply operation

— On-chip regulator 5 V to 3.3 V for internal supplies

— On-chip regulator controller 5 V to 1.2 V (with external bypass transistor) for core logic

•

Low-power modes

— SLOW Mode. Allows device to be run at very low speed (approximately 1 MHz), with 

modules (including the PLL) selectively disabled in software

— STOP Mode. System clock stopped to all modules including the CPU. Wake-up timer used to 

restart the system clock after a predetermined time

•

Package

— Available in 144 LQFP (20mm x 20mm, 0.5mm pitch), 208 MAPBGA (17mm x 17mm)

1.4.2

e200z335 Core

The e200z335 processor utilizes a four stage pipeline for instruction execution. The Instruction Fetch 
(stage 1), Instruction Decode/Register file Read/Effective Address Calculation (stage 2), Execute/Memory 
Access (stage 3), and Register Writeback (stage 4) stages operate in an overlapped fashion, allowing single 
clock instruction execution for most instructions. 

The integer execution unit consists of a 32-bit Arithmetic Unit (AU), a Logic Unit (LU), a 32-bit Barrel 
shifter (Shifter), a Mask-Insertion Unit (MIU), a Condition Register manipulation Unit (CRU), a 
Count-Leading-Zeros unit (CLZ), a 32x32 Hardware Multiplier array, result feed-forward hardware, and 
support hardware for division. 

Most arithmetic and logical operations are executed in a single cycle with the exception of the divide 
instructions. A Count-Leading-Zeros unit operates in a single clock cycle. The Instruction Unit contains a 
PC incrementer and a dedicated Branch Address adder to minimize delays during change of flow 
operations. Sequential prefetching is performed to ensure a supply of instructions into the execution 
pipeline. Branch target prefetching is performed to accelerate taken branches. Prefetched instructions are 
placed into an instruction buffer capable of holding six instructions. 

Branches can also be decoded at the instruction buffer and branch target addresses calculated prior to the 
branch reaching the instruction decode stage, allowing the branch target to be prefetched early. When a 
branch is detected at the instruction buffer, a prediction may be made on whether the branch is taken or 
not. If the branch is predicted to be taken, a target fetch is initiated and its target instructions are placed in 
the instruction buffer following the branch instruction. Many branches take zero cycle to execute by using 
branch folding. Branches are folded out from the instruction execution pipe whenever possible. These 
include unconditional branches and conditional branches with condition codes that can be resolved early.

 Conditional branches which are not taken and not folded execute in a single clock. Branches with 
successful target prefetching which are not folded have an effective execution time of one clock. All other 
taken branches have an execution time of two clocks. Memory load and store operations are provided for 

Содержание MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды