Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 529 | Manualshive

Страница: 529 / 1153

background image

Flash Memory

MPC5565 Microcontroller Reference Manual, Rev. 1.0

13-14

Freescale Semiconductor

13.3.2.3

High Address Space Block Locking Register (FLASH_HLR)

The high address space block locking register provides a means to protect blocks from being modified.

13.3.2.4

Secondary Low/Mid Address Space Block Locking Register
(FLASH_SLMLR)

The FLASH_SLMLR provides an alternative means to protect blocks from being modified. These bits
along with bits in the LMLOCK field (FLASH_LMLR), determine if the block is locked from program or
erase. An “OR” of FLASH_LMLR and FLASH_SLMLR determine the final lock status. Refer to

Section 13.3.2.2, “Low/Mid Address Space Block Locking Register (FLASH_LMLR)

information on FLASH_LMLR.

Address: Base (0xC3F8_8000) + 0x0008

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R HBE 0

0

0

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

HLOCK

W

Reset

0

0

0

0 1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

The reset value of these bits is determined by flash values in the shadow row. An erased array causes the reset value
to be 1.

Figure 13-7. High Address Space Block Locking Register (FLASH_HLR)

Table 13-8. FLASH_HLR Field Descriptions

Field

Description

0

HBE

High address lock enable. Enables the locking field (HLOCK) to be set or cleared by register writes. This bit
is a status bit only, and cannot be written to or cleared, and the reset value is 0. The method to set this bit
is to provide a password, and if the password matches, the HBE bit is set to reflect the status of enabled,
and is enabled until a reset operation occurs. For HBE, the password 0xB2B2_2222 must be written to
FLASH_HLR.
0 High address locks are disabled, and cannot be modified.
1 High address locks are enabled to be written.

1–19

Reserved.

20–31

HLOCK[11:0]

High address space block lock. Has the same characteristics as MLOCK. Refer to

Section 13.3.2.2,

“Low/Mid Address Space Block Locking Register (FLASH_LMLR)

” for more information. The block

numbering for High Address space starts with HLOCK[0] and continues until all blocks are accounted.
HLOCK is not writable unless HBE is set.
In the event that blocks are not present (due to configuration or total memory size), the HLOCK bits are
default to locked, and are not writable.

«
...
527
528
529
530
531
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Jabra Страницы: 8

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: Talgil Страницы: 14

Бренд: Full Gauge Controls Страницы: 3

Бренд: Casambi Страницы: 2

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

Бренд: Teledyne Страницы: 102

Бренд: Samson Страницы: 70

Бренд: Kantronics Страницы: 201

Freescale Xtrinsic LFSTBEB865X

Бренд: NXP Semiconductors Страницы: 2

Бренд: Swagelok Страницы: 6

AquaController Apex

Бренд: Neptune Systems Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды