manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Interrupt Controller (INTC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

10-33

 

OSEK uses the GetResource and ReleaseResource system services to manage access to a shared resource. 
To prevent this corruption of a coherent data block, modifications to PRI in INTC_CPR can be made by 
those system services with the following code sequences.

GetResource:

raise PRI

mbar

isync

ReleaseResource:

mbar

lower PRI

10.5.6

Selecting Priorities According to Request Rates 
and Deadlines

The selection of the priorities for the ISRs can be made using rate monotonic scheduling (RMS) or a 
superset of it, deadline monotonic scheduling (DMS). In RMS, the ISRs which have higher request rates 
have higher priorities. In DMS, if the deadline is before the next time the ISR is requested, then the ISR is 
assigned a priority according to the time from the request for the ISR to the deadline, not from the time of 
the request for the ISR to the next request for it.

For example, ISR1 executes every 100 

μ

s, ISR2 executes every 200 

μ

s, and ISR3 executes every 300 

μ

s. 

ISR1 has a higher priority than ISR2 which has a higher priority than ISR3. However, if ISR3 has a 
deadline of 150 

μ

s, then it has a higher priority than ISR2.

The INTC has 16 priorities, which could be much less than the number of ISRs. In this case, group the 
ISRs with other ISRs that have similar deadlines. For example, a priority could be allocated for every time 
the request rate doubles. ISRs with request rates around 1 ms would share a priority, ISRs with request 
rates around 500 

μ

s would share a priority, ISRs with request rates around 250 

μ

s would share a priority, 

etc. With this approach, a range of ISR request rates of 2

16

 could be covered, regardless of the number of 

ISRs.

Reducing the number of priorities does reduce the processor's ability to meet its deadlines. However, it 
also allows easier management of ISRs with similar deadlines that share a resource. They do not need to 
use the PCP to access the shared resource.

10.5.7

Software Settable Interrupt Requests

The software settable interrupt requests can be used in two ways. They can be used to schedule a lower 
priority portion of an ISR and for processors to interrupt other processors in a multiple processor system.

10.5.7.1

Scheduling a Lower Priority Portion of an ISR

A portion of an ISR needs to be executed at the PRI

n

 value in INTC priority select registers 

(INTC_PSR0–INTC_PSR231), which becomes the PRI value in INTC current priority register 
(INTC_CPR) with the interrupt acknowledgement. The ISR, however, can have a portion of it which does 
not need to be executed at this higher priority. Therefore, executing this later portion which does not need 
to be executed at this higher priority can prevent the execution of ISRs which do not have a higher priority 

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Vageo DT-1 Plus Manual preview
DT-1 Plus
Бренд: Vageo Страницы: 2
Vacon 100 INDUSTRIAL Additional Installation Instruction preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 6
Vacon 100 INDUSTRIAL Technical Manual preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 24
Vacon 100X series Marine Installation Manual preview
100X series
Бренд: Vacon Страницы: 30
Vacon 100 flow User Manual preview
100 flow
Бренд: Vacon Страницы: 81
Vacon 100X series Installation And Maintenance Manual preview
100X series
Бренд: Vacon Страницы: 100
ZPA Pecky, a.s. 52 442 Mounting Instructions preview
52 442
Бренд: ZPA Pecky, a.s. Страницы: 36
Danfoss 084B8012 Instructions Manual preview
084B8012
Бренд: Danfoss Страницы: 30
Greenheck MP-220A Installation, Operation And Maintenance Manual preview
MP-220A
Бренд: Greenheck Страницы: 4
Cypress CY3280-BK1 Quick Start Manual preview
CY3280-BK1
Бренд: Cypress Страницы: 3
Qorvo QM33120WDK1 Quick Start Manual preview
QM33120WDK1
Бренд: Qorvo Страницы: 6
Carrier 40BNC Installation Instructions preview
40BNC
Бренд: Carrier Страницы: 4
Danfoss MCD 600 Installation Manual preview
MCD 600
Бренд: Danfoss Страницы: 22
Savant SmartControl RS232 Quick Reference Manual preview
SmartControl RS232
Бренд: Savant Страницы: 2
M-Audio Keyboard Controller Series Quick Start Manual preview
Keyboard Controller Series
Бренд: M-Audio Страницы: 2
Roth Touchline PL 2 Ch Installation Manual preview
Touchline PL 2 Ch
Бренд: Roth Страницы: 8
Altronic DE-2500 Installation & Operating Instructions Manual preview
DE-2500
Бренд: Altronic Страницы: 70
Samson series 43 Mounting And Operating Instructions preview
series 43
Бренд: Samson Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды