Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 366 | Manualshive

Страница: 366 / 1153

background image

Enhanced Direct Memory Access (eDMA)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

9-41

This can cause the same bandwidth problem indicated in Section 9.4.4.1, but all the channels in the highest
priority group are serviced. Service latency is short on the highest-priority group, but increases as the
group priority decreases.

9.4.5

DMA Transfer

9.4.5.1

Single Request

To perform a simple transfer of ‘

n

’ bytes of data with one activation, set the major loop to 1

(TCD.CITER = TCD.BITER = 1). The data transfer begins after the channel service request is
acknowledged and the channel is selected to execute. After the transfer completes, the TCD.DONE bit is
set and an interrupt is generated if correctly enabled.

For example, the following TCD entry is configured to transfer 16 bytes of data. The eDMA is
programmed for one iteration of the major loop transferring 16 bytes per iteration. The source memory has
a byte-wide memory port located at 0x1000. The destination memory has a word-wide port located at
0x2000. The address offsets are programmed in increments to match the size of the transfer; one byte for
the source and four bytes for the destination. The final source and destination addresses are adjusted to
return to their beginning values.

TCD.CITER = TCD.BITER = 1

TCD.NBYTES = 16

TCD.SADDR = 0x1000

TCD.SOFF = 1

TCD.SSIZE = 0

TCD.SLAST = –16

TCD.DADDR = 0x2000

TCD.DOFF = 4

TCD.DSIZE = 2

TCD.DLAST_SGA= –16

TCD.INT_MAJ = 1

TCD.START = 1 (Initialize all other fields before writing to this bit)

All other TCD fields = 0

This generates the following sequence of events:

1. Slave write to the TCD.START bit requests channel service.

2. The channel is selected by arbitration for servicing.

3. eDMA engine writes: TCD.DONE = 0, TCD.START = 0, TCD.ACTIVE = 1.

4. eDMA engine reads: channel TCD data from local memory to internal register file.

5. The source to destination transfers are executed as follows:

a) read_byte (0x1000), read_byte(0x1001), read_byte(0x1002), read_byte(0x1003)

b) write_word (0x2000) -> first iteration of the minor loop

«
...
364
365
366
367
368
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

GAT ACCESS 6100

Бренд: Gantner Страницы: 4

Бренд: GCE Страницы: 24

Бренд: H3C Страницы: 27

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 54

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 10

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: MacroAir Technologies Страницы: 32

Бренд: McIntosh Страницы: 68

Бренд: Cypress Страницы: 2

Бренд: Dudley Страницы: 8

Бренд: Raypak Страницы: 2

Бренд: SFC Страницы: 48

Бренд: Satel Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды