Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1020 | Manualshive

Страница: 1020 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-27

24.9

Nexus Single eTPU Development Interface (NSEDI)

The enhanced timing processor unit (eTPU) has its own Nexus class 3 interface, the Nexus single eTPU
development interface (NSEDI). The single eTPU engine and a coherent dual parameter controller (CDC)
appear as two separate Nexus clients. Refer to the

Enhanced Time Processor Unit Reference Manual

for

more information about the NSEDI module.

24.10 e200z6 Class 3 Nexus Module (NZ6C3)

The NZ6C3 module provides real-time development capabilities for the device core in compliance with
the IEEE

®

-ISTO Nexus 5001-2003 standard. This module provides development support capabilities

without requiring the use of address and data pins for internal visibility.

24.10.1 Introduction

This section defines the auxiliary pin functions, transfer protocols and standard development features of
the NZ6C3 module. The development features supported are Program trace, data trace, watchpoint
messaging, ownership trace, and read/write access via the JTAG interface.

Reg Index: 0

Access: R/O

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

R

PRN

DC

PIN

W

Reset

0

0

0

0

1

0

0

0

0

0

0

1

0

0

1

0

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

PIN

MIC

1

W

Reset

0

1

0

0

0

0

0

0

0

0

0

1

1

1

0

1

Figure 24-12. NSEDI Device ID Register (DID)

Table 24-17. NSEDI DID Register Field Descriptions

Field

Description

31–28

PRN

Part revision number. Contains the revision number of the part. This field changes with each revision of the
device or module.

27–22

DC

Design center. Indicates the Freescale design center. This value is 0x20.

21–12

PIN

Part identification number. Contains the part number of the device. The PIN for the MPC5565 is 0x124.

11–1

MIC

Manufacturer identity code. Contains the reduced Joint Electron Device Engineering Council (JEDEC) ID
for Freescale, 0xE.

0

Fixed per JTAG 1149.1
1 Always set

«
...
1018
1019
1020
1021
1022
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

MorphoAccess SIGMA Extreme Series

Бренд: Safran Страницы: 79

Бренд: Lawler Страницы: 5

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Бренд: IFM Electronic Страницы: 23

CEmarking RCX221

Бренд: Yamaha Страницы: 468

WISE-224 Series

Бренд: ICP DAS USA Страницы: 8

Бренд: Fisher Страницы: 44

SATLOC GPSteer LiteStar II

Бренд: CSI Wireless Страницы: 7

Бренд: Icom Страницы: 23

Triton UltraLift

Бренд: HydroHoist Страницы: 9

Бренд: YOKOGAWA Страницы: 12

SUNEXPLORER III Series

Бренд: Atkinson Electronics Страницы: 22

Mi-Light FUT089Z

Бренд: Miboxer Страницы: 12

5268 Servocontrol

Бренд: Viessmann Страницы: 4

Бренд: Spektrum Страницы: 2

Бренд: ESYLUX Страницы: 12

Бренд: BBB Страницы: 14

Бренд: DELTA DORE Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды