manualshive.com logo in svg

Freescale Semiconductor MCF5329, Справочное руководство, Страница: 728 / 924

Поделиться
Скачать
Freescale Semiconductor MCF5329 Скачать руководство пользователя страница 728

UART Modules

31-8

Freescale Semiconductor

31.3.3

UART Status Registers (USRn)

The USR

n 

registers show the status of the transmitter, the receiver, and the FIFO.

Address: 0xFC06_0004 (USR0)

0xFC06_4004 (USR1)
0xFC06_8004 (USR2)

Access: User read-only

7

6

5

4

3

2

1

0

R

RB

FE

PE

OE

TXEMP

TXRDY

FFULL

RXRDY

W

Reset:

0

0

0

0

0

0

0

0

Figure 31-5. UART Status Registers (USRn)

Table 31-5. USRn Field Descriptions

Field

Description

7

RB

Received break. The received break circuit detects breaks originating in the middle of a received character. However, 
a break in the middle of a character must persist until the end of the next detected character time. 
0 No break was received.
1 An all-zero character of the programmed length was received without a stop bit. Only a single FIFO position is 

occupied when a break is received. Further entries to the FIFO are inhibited until UnRXD returns to the high state 
for at least one-half bit time, which equals two successive edges of the UART

 

clock. RB is valid only when RXRDY 

is set.

6

FE

Framing error. 
0 No framing error occurred.
1 No stop bit was detected when the corresponding data character in the FIFO was received. The stop-bit check 

occurs in the middle of the first stop-bit position. FE is valid only when RXRDY is set.

5

PE

Parity error. Valid only if RXRDY is set. 
0 No parity error occurred.
1 If UMR1n[PM] equals 0x (with parity or force parity), the corresponding character in the FIFO was received with 

incorrect parity. If UMR1n[PM] equals 11 (multidrop), PE stores the received address or data (A/D) bit. PE is valid 
only when RXRDY is set.

4

OE

Overrun error. Indicates whether an overrun occurs. 
0 No overrun occurred.
1 One or more characters in the received data stream have been lost. OE is set upon receipt of a new character 

when the FIFO is full and a character is already in the shift register waiting for an empty FIFO position. When this 
occurs, the character in the receiver shift register and its break detect, framing error status, and parity error, if any, 
are lost. The 

RESET

 

ERROR

 

STATUS

 command in UCRn clears OE.

3

TEMP

Transmitter empty. 
0 The transmit buffer is not empty. A character is shifted out, or the transmitter is disabled. The transmitter is 

enabled/disabled by programming UCRn[TC].

1 The transmitter has underrun (the transmitter holding register and transmitter shift registers are empty). This bit 

is set after transmission of the last stop bit of a character if there are no characters in the transmitter holding 
register awaiting transmission.

2

TXRDY

Transmitter ready.
0 The CPU loaded the transmitter holding register, or the transmitter is disabled.
1 The transmitter holding register is empty and ready for a character. TXRDY is set when a character is sent to the 

transmitter shift register or when the transmitter is first enabled. If the transmitter is disabled, characters loaded 
into the transmitter holding register are not sent.

MCF5329 Reference Manual, Rev 3

Содержание MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов