manualshive.com logo in svg

Freescale Semiconductor MCF5329, Справочное руководство, Страница: 283 / 924

Поделиться
Скачать
Freescale Semiconductor MCF5329 Скачать руководство пользователя страница 283

Interrupt Controller Modules

Freescale Semiconductor

14-15

14.2.10 Software and Level 1 – 7 IACK Registers (SWIACKn, L1IACKn – 

L7IACKn)

The eight IACK registers (per interrupt controller) can be explicitly addressed via the CPU, or implicitly 
addressed via a processor-generated interrupt acknowledge cycle during exception processing. In either 
case, the interrupt controller’s actions are very similar.

First, consider an IACK cycle to a specific level: a level-

n

 IACK. When this type of IACK arrives in the 

interrupt controller, the controller examines all the currently-active level 

n

 interrupt requests, determines 

the highest priority within the level, and then responds with the unique vector number corresponding to 
that specific interrupt source. The vector number is supplied as the data for the byte-sized IACK read cycle. 
In addition to providing the vector number, the interrupt controller also loads the level into the CLMASK 
register, where it may be retrieved later.

This interrupt controller design also supports the concept of a software IACK. A software IACK allows 
an interrupt service routine to determine if there are other pending interrupts so that the overhead 
associated with interrupt exception processing (including machine state save/restore functions) can be 
minimized. In general, the software IACK is performed near the end of an interrupt service routine, and if 
there are additional active interrupt sources, the current interrupt service routine (ISR) passes control to 
the appropriate service routine, but without taking another interrupt exception.

When the interrupt controller receives a software IACK read, it returns the vector number associated with 
the highest unmasked interrupt source for that interrupt controller. If there are no active sources, the 
interrupt controller returns an all-zero vector as the operand for the SWIACK register. A read from the 
L

n

IACK registers when there are no active requests returns a value of 24 (0x18), signaling a spurious 

interrupt.

In addition to the software IACK registers in each interrupt controller, there are global software IACK 
registers. A read from the global SWIACK (GSWIACK) returns the vector number for the highest level 
and priority unmasked interrupt source from all interrupt controllers. A read from one of the global 
L

n

IACK (GL

n

IACK) registers returns the vector for the highest priority unmasked interrupt within a level 

for all interrupt controllers.

51

LCDC

LCD_ISR

LCD controller interrupt

Read the LCD_ISR register.

52

RTC

RTC_ISR

Real time clock interrupt

Write one to corresponding bit in RTC_ISR.

53

CCM

UHCSR or UOCSR

USB status Interrupt

Read UHCSR or read UOCSR.

54–63

Not Used

Table 14-16. Interrupt Source Assignment for  INTC1 (continued)

Source Module

 

Flag

Source 

Description

Flag Clearing Mechanism

MCF5329 Reference Manual, Rev 3

Содержание MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов