manualshive.com logo in svg

Freescale Semiconductor MCF5329, Справочное руководство, Страница: 276 / 924

Поделиться
Скачать
Freescale Semiconductor MCF5329 Скачать руководство пользователя страница 276

Interrupt Controller Modules

14-8

Freescale Semiconductor

14.2.5

Set Interrupt Mask Register (SIMRn)

The SIMR

n

 register provides a simple mechanism to set a given bit in the IMR

n

 registers to mask the 

corresponding interrupt request. The value written to the SIMR field causes the corresponding bit in the 
IMR

n

 register to be set. The SIMR

n

[SALL] bit provides a global set function, forcing the entire contents 

of IMR

n

 to be set, thus masking all interrupts. Reads of this register return all zeroes. This register is 

provided so interrupt service routines can easily mask the given interrupt request without the need to 
perform a read-modify-write sequence on the IMR

n

 register.

Table 14-9. ICONFIG Field Descriptions 

Field

Description

15–9

ELVLPRI

Enable core’s priority elevation on priority levels. Each ELVLPRI[7:1] bit corresponds to the available priority 

levels 1 – 7. If set, the assertion of the corresponding level-n request to the core causes the processor’s bus 
master priority to be temporarily elevated in the device’s crossbar switch arbitration logic. The processor’s bus 
master arbitration priority remains elevated until the level-n request is negated. If round-robin arbitration is 
enabled, this bit has no effect.

If cleared, the assertion of a level-n request does not affect the processor’s bus master priority. 

8–6

Reserved, must be cleared.

5

EMASK

If set, the interrupt controller automatically loads the level of an interrupt request into the CLMASK (current level 
mask) when the acknowledge is performed. At the exact same cycle, the value of the current interrupt level mask is 
saved in the SLMASK (saved level mask) register.
This feature can be used to support software-managed nested interrupts, and is intended to complement the 
interrupt masking functions supported in the ColdFire processor. The value of SLMASK register should be read from 
the interrupt controller and saved in the interrupt stack frame in memory, and restored near the service routine’s exit.
If cleared, the INTC does not perform any automatic masking of interrupt levels. The state of this bit does not affect 
the ColdFire processor’s interrupt masking logic in any manner.

4–0

Reserved, must be cleared.

Address: 0xFC04_801C (SIMR0)

0xFC04_C01C (SIMR1)

Access: User write-only

7

6

5

4

3

2

1

0

R

0

0

0

0

0

0

0

0

W

SALL

SIMR

Reset:

0

0

0

0

0

0

0

0

Figure 14-8. Set Interrupt Mask Register (SIMRn)

Table 14-10. SIMRn Field Descriptions

Field

Description

7

Reserved, must be cleared.

6

SALL

Set all bits in the IMRn register, masking all interrupt requests. 
0 Only set those bits specified in the SIMR field.
1 Set all bits in IMRn register. The SIMR field is ignored.

5–0

SIMR

Set the corresponding bit in the IMRn register, masking the interrupt request.

MCF5329 Reference Manual, Rev 3

Содержание MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов