manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVM series, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor MC9S12ZVM series Скачать руководство пользователя страница 545

Chapter 14 Pulse Width Modulator with Fault Protection (PMF15B6CV3)

MC9S12ZVM Family Reference Manual Rev. 1.3

Freescale Semiconductor

545

Figure 14-72. Setting asserted LDOK bit at PWM reload event

14.4.12.2 Global Load Enable

If a global load enable bit GLDOKA, B, or C is set, the global load OK bit defined on device level as input
to the PMF replaces the function of the related local LDOKA, B, or C bits. The global load OK signal is
typically shared between multiple IP blocks with the same double buffer scheme. Software handling must
be transferred to the global load OK bit at the chip level.

14.4.12.3 Load Frequency

The LDFQ3, LDFQ2, LDFQ1, and LDFQ0 bits in the PWM control register (PMFFQCx) select an
integral loading frequency of 1 to 16-PWM reload opportunities. The LDFQ bits take effect at every PWM
reload opportunity, regardless the state of the related load okay bit or global load OK. The

half

bit in the

PMFFQC register controls half-cycle reloads for center-aligned PWMs. If the

half

bit is set, a reload

opportunity occurs at the beginning of every PWM cycle and half cycle when the count equals the
modulus. If the half bit is not set, a reload opportunity occurs only at the beginning of every cycle. Reload
opportunities can only occur at the beginning of a PWM cycle in edge-aligned mode.

NOTE

Setting the half bit takes effect immediately. Depending on whether the
counter is incrementing or decrementing at this point in time, reloads at
even-numbered reload frequencies (every 2, 4, 6,... reload opportunities)
will occur only when the counter matches the modulus or only when the
counter equals zero, respectively (refer to example of reloading at every two
opportunities in

Figure 14-74

).

NOTE

Loading a new modulus on a half cycle will force the count to the new
modulus value minus one on the next clock cycle. Half cycle reloads are
possible only in center-aligned mode. Enabling or disabling half-cycle
reloads in edge-aligned mode will have no effect on the reload rate.

bus clock

LDOK write

LDOK bit

PWM reload

bus clock

LDOK write

LDOK bit

PWM reload

Содержание MC9S12ZVM series


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды