Freescale Semiconductor e200z3 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 442

background image

Register Model

e200z3 Power Architecture Core Reference Manual, Rev. 2

Freescale Semiconductor

2-19

2.7.2

Accumulator (ACC)

The 64-bit architectural accumulator register holds the results of the multiply accumulate (MAC) forms of
SPE integer instructions. The accumulator allows back-to-back execution of dependent MAC instructions,
as in the inner loops of DSP code such as finite impulse response (FIR) filters. The accumulator is partially
visible to the programmer in that its results do not have to be explicitly read to use them. Instead, they are
always copied into a 64-bit destination GPR specified as part of the instruction. However, the accumulator
must be explicitly initialized when a new MAC loop starts. Based upon the type of instruction, an
accumulator can hold either a single 64-bit value or a vector of two 32-bit elements.

The Initialize Accumulator instruction (evmra) initializes the accumulator. This instruction is described
in the EREF.

2.8

Interrupt Registers

This section describes the registers for interrupt handling.

2.8.1

Interrupt Registers Defined by Book E

This section describes the following registers and their fields:

•

Section 2.8.1.1, “Save/Restore Register 0 (SRR0)”

•

Section 2.8.1.2, “Save/Restore Register 1 (SRR1)”

•

Section 2.8.1.3, “Critical Save/Restore Register 0 (CSRR0)”

•

Section 2.8.1.4, “Critical Save/Restore Register 1 (CSRR1)”

•

Section 2.8.1.5, “Data Exception Address Register (DEAR)”

•

Section 2.8.1.6, “Interrupt Vector Prefix Register (IVPR)”

•

Section 2.8.1.7, “Interrupt Vector Offset Registers (IVORs)”

•

Section 2.9, “Exception Syndrome Register (ESR)”

60

FUNFE Embedded floating-point underflow exception enable.

0 Exception disabled.
1 Exception enabled. A floating-point data exception is taken if FUNF or FUNFH is set by a floating-point

instruction.

61

FOVFE Embedded floating-point overflow exception enable.

0 Exception disabled.
1 Exception enabled. If the exception is enabled, a floating-point data exception is taken if FOVF or FOVFH

is set by a floating-point instruction.

62–63

FRMC

Embedded floating-point rounding mode control.
00  Round to nearest.
01  Round toward zero.
10  Round infinity.
11  Round toward -infinity.

Table 2-9. SPEFSCR Field Descriptions (continued)

Bits

Name

Description

«
...
65
66
67
68
69
...
»

Содержание e200z3



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для e200z3

COMSPHERE 3800 Series

Бренд: Paradyne Страницы: 88

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 5

Бренд: T&D Страницы: 122

Бренд: Datasat Страницы: 170

Бренд: 3Ware Страницы: 4

4 Channel Input Buffer Board SDAIBB

Бренд: B&B Electronics Страницы: 22

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

Бренд: QTech Страницы: 406

Бренд: Xilinx Страницы: 27

Бренд: ETAS Страницы: 36

Бренд: ICOP Technology Страницы: 42

Бренд: Xinje Страницы: 76

Бренд: Juniper Страницы: 6

EK-Quantum Vector TUF RX 6800

Бренд: ekwb Страницы: 14

STM32MP157 Series

Бренд: ST Страницы: 47

Бренд: Infoblox Страницы: 44

Бренд: CAMBRIONIX Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды