Freedom Lite Business 40/32 Скачать руководство пользователя

Страница: 30 / 30

Freedom Lite Installation Manual Revision 12

P a g e

29 | 30

The Freedom Lite error light

keeps illuminating after each

reset

If the battery voltage is within limits this should not

ordinarily occur. Contact Freedom Won or an approved

installer for assistance with determining the problem. If

the main breaker does not trip it is not a critical error

and you may continue using the battery while you make

contact for assistance.

10 The pack voltage is within limits,

but the main breaker still trips

seemingly at random

This could be caused by many things but is most likely

because the current draw is exceeding the battery

current limit setting. Measure the current with a tong

tester while drawing your maximum typical load to

determine if you are exceeding the rated current for the

respective Freedom Lite model. If it is not the current

causing the trip it could be a weak cell or extreme

temperature of the surroundings. Both are unlikely. If

the problem persists, contact Freedom Won.

Содержание Lite Business 40/32































Результаты поиска

Содержание Lite Business 40/32

Отзывы:

Похожие инструкции для Lite Business 40/32

Бренды по названию

Популярные бренды

Freedom Lite Business 40/32, Руководство по установке

Результаты поиска

Содержание Lite Business 40/32

Отзывы:

Похожие инструкции для Lite Business 40/32

Бренды по названию

Популярные бренды