manualshive.com logo in svg

Franklin Fueling Systems GUARDIAN SPGC-220., Руководство по установке

Поделиться
Скачать
Franklin Fueling Systems GUARDIAN SPGC-220. Скачать руководство пользователя страница 21

17

Overload alarm

Error code flashes: OL or Lr
The Overload (while running) and Locked Rotor (at startup) alarms indicate that the SPGC-
220 has detected that the motor power consumption (in watts) is above the acceptable range 
compared to the calibration value. The Overload (OL) and Locked Rotor (Lr) alarms are usually 
caused by a locked PMA rotor (due to debris or damage) or improper calibration.

Was the PMA  

replaced with a 

new PMA of the 

same horsepower?

Press and hold the Reset button 

until the display goes blank.

Release the Reset button.

Lock and tag out the STP 

circuit breaker.

Monitor 

for proper 

operation.

Calibrate 

the 

controller.

Proceed to the STP sump.

No

No

Yes

Did the 

fault clear?

A

Yes

No

Yes

Energize the hook signal.

Did the 

controller go 

into the OL or Lr 

error code?

Yes

No

Was the 

calibration 

successful?

Monitor 

for proper 

operation.

Содержание GUARDIAN SPGC-220.





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды