Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 156

background image

COMMUNICATIONS

BACnet Communication

91

BACnet Device ID Setup

The BACnet Device Object Identifier is the combination of

Device ID Lo [COMM-26]

and

Device ID Hi

[COMM-27]

, representing the lower and upper hexadecimal values respectively.

The

Device ID Lo [COMM-26]

value is usually a unique device number in the trunk. It must be within a

range from 0 to 65535. The

Device ID Hi [COMM-27]

is usually set to the trunk or building floor number,

and must be a value within a range from 0 to 63.
The calculation of the BACnet Device ID is

[COMM-27]

* 65536 +

[COMM-26]

. This value must be within a

range from 0 to 4194303.
•

If the BACnet Device ID is less than 65536, no calculation is needed;

[COM-27]

is always 0 and

[COM-26]

equals the BACnet Device ID.

For example, if the BACnet ID is 10025, set

[COMM-27]

to 0 and

[COMM-26]

to 10025.

•

For a BACnet Device ID greater than 65535, calculate the BACnet ID / 65536 to get a value with a
remainder. To figure out the remainder value, take BACnet Device ID - (value * 65536). Set

[COMM-27]

to the calculated value and [COMM-26] to the remainder.
For example, if the BACnet Device ID is 842334, then 842334 / 65536 equals value 12 with a remainder.
The remainder value is calculated out by 842334 - (12 * 65536) = 55802. Therefore,

[COMM-27]

should

be set to 12 and

[COMM-26]

should be set to 55802.

BACnet Objects

Commandable Analog Value Objects

Status Analog Value Objects (Read Only)

Object Number

R/W

Object Name

Object Description

Unit

AV 000

RW Reserved

–

–

AV 001

RW FreqRefValue

Frequency Reference Value

Hz

AV 002 through AV 010

RW Reserved

–

–

AV 011 through AV 026

RW Block Transfer

Block transfer mapping 1 to 16

Dependent

Object Number

R/W

Object Name

Object Description

Unit

AV 027 through AV 030

R Reserved

–

–

AV 031

R Output Frequency

Output Frequency Value

Hz

AV 032 through AV 034

R Reserved

–

–

AV 035

R Output Torque

Output Torque

%

AV 036 through AV 038

R Reserved

–

–

AV 039

R Status Word

VFD Status Word from BV 16 through BV 31

–

AV 040

R Reserved

–

–

AV 041

R Drive Type Code

Drive Type Code

–

AV 042

R Warning Code

Warning/Alarm Code

–

AV 043

R Error Code

Error/Fault Code

–

AV 044

R Output Current

Output/Motor Current

Amperes

AV 045

R DC Bus Voltage

DC Bus Voltage

VDC

AV 046

R Output Voltage

Output Voltage

VAC

AV 047

R Count Value

Accumulated TRG DI Counter Value

–

AV 048

R Power Factor

Output Power Factor

–

AV 049

R Output Power

Output Power

kW

AV 050

R IGBT Temperature

IGBT Temperature

° C

AV 051

R Caps Temperature

DC Bus Capacitors Temperature

° C

AV 052

R Carrier Frequency

Actual Carrier Frequency

kHz

«
...
89
90
91
92
93
...
»

Содержание Cerus X-Drive





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cerus X-Drive

Бренд: ECG Страницы: 15

Бренд: Graco Страницы: 4

Бренд: Magnetek Страницы: 119

Бренд: Vaidnor Страницы: 166

Бренд: Fostex Страницы: 6

Бренд: BTR Страницы: 28

DVR 115D - DVD±RW Drive - IDE

Бренд: Pioneer Страницы: 2

DVR 116D - DVD±RW Drive - IDE

Бренд: Pioneer Страницы: 4

DVR 115D - DVD±RW Drive - IDE

Бренд: Pioneer Страницы: 5

Бренд: Pioneer Страницы: 1

Бренд: Pioneer Страницы: 5

Бренд: Pioneer Страницы: 8

Бренд: Pioneer Страницы: 8

Бренд: Pioneer Страницы: 8

BDC-2202 - DVD±RW / DVD-RAM

Бренд: Pioneer Страницы: 2

Бренд: Pioneer Страницы: 17

215D - DVR - Disk Drive

Бренд: Pioneer Страницы: 4

Бренд: Pioneer Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды