Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 81

Страница: 81 / 156

ADVANCED APPLICATION OPTIONS

Operation with Permanent Magnet Motors

Motor Specific Parameters

For MagForce applications, the drive automatically sets:
•

PM Rs [Motor-09]:

Motor stator resistance.

•

PM Ld [Motor-10]:

Motor inductance d-axis.

•

PM Lq [Motor-11]:

Motor inductance q-axis.

•

PM Ke Coeff [Motor-13]:

Motor parameter Ke (Vphase, rms / krpm).

Autotune Characteristic Parameters

For MagForce applications, autotune is not needed. However, if the drive consistently exceeds the motor
current specification during DC Alignment and I/F control, then an autotune may be needed. Refer to

“Autotune Characteristic Parameters” on page 82

Tune motor control – DC Alignment

For MagForce applications, no adjustments are needed. However, if there are problems during DC Align

ment, refer to

“Tune motor control – DC Alignment” on page 82

Tune motor control - I/F Control

For MagForce applications, no adjustments are needed. However, if there are problems during I/F Control,
refer to

“Tune motor control - I/F Control” on page 82

Tune motor control - PM Control

For MagForce applications, no adjustments are needed. However, if there are problems during PM Control,
refer to

“Tune motor control - PM Control” on page 83

Setup Non-Franklin Electric PM Motors

The X-Drive can be programmed to operate general purpose permanent magnet motors through the follow

ing procedure:

Basic Setup

IMPORTANT:

If the VFD has been used in a previous application, the drive parameters should be completely

reset using

Parameter Reset [ADV–03]

, option

4_Reset all Param

Application [SET–00]:

Set to option 8_PM Motor. This selection assumes the use of a 4-pole, 3-phase

PM motor running at 120 Hz and automatically updatesrelevant parameters to the proper defaults.

IMPORTANT:

NOT

use the MagForce selection with non-Franklin Electric permanent magnet

motors.

Input Phase [SET–01]:

Verify that the setting matches the type of power supply— 3-phase (default).

Motor Horsepower [SET–02]:

Enter the maximum rated horsepower from the motor nameplate.

Motor FLA (SFA) [SET–03]:

Enter the rated motor FLA, found on the motor nameplate.

Motor RPM [SET–04]:

Enter the rated motor RPM from the motor nameplate.

Motor Voltage [SET–05]:

Enter the rated voltage from the motor nameplate.

VFD Max Freq [VFD–00]:

The highest frequency (speed) allowable.

VFD Base Freq [VFD–02]:

This should be set to the motor nameplate frequency rating.

Carrier Freq [SET–06]:

This should be set to 4 kHz for sine filters and 2 kHz for dV/dt filters. Carrier

frequency should be at least 1.5 times the resonant frequency of the filter.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды