Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 156

background image

OPERATION

Protection Features

77

If the run command is removed, or HOA is set to OFF, the Underload feature is canceled and the [Set–
45] timer is reset to its original setting.

Fine Tune Settings for ULD by Torque

1.

Verify accuracy of Motor FLA (SFA) [Set–03], Motor Voltage [Set–05], and VFD Base Freq [VFD–02].
These values determine nominal torque.

2. Adjust ULD Frequency [Set–43] to be equal to minimum operational frequency [Set–13] or [Set–22].
3. Run motor at minimum frequency and verify water movement for pump or air movement for fans.
4. While running the motor at minimum frequency, determine whether VFD trips on ULD:

•

If system trips on HLD using default ULD Level [Set–42], decrease level by 03% until system does
not trip.

•

If system does NOT trip using default ULD Level [Set–42], increase the level by increments of 3%
until system trips, then decrease back by 3%.

5. If nuisance tripping occurs, lower ULD Min Torque [Prot–57] by increments of 1%.
6. Adjust ULD Delay [Set–44] to duration acceptable for operation.
7. Adjust ULD Recovery Time [Set–45] to a duration that fills-up well enough to allow motor to run mini

-

mum time before another ULD trip.

Overpressure

The Overpressure feature stops the VFD when PID feedback exceeds a set value in either Hand or Auto.
To enable this feature, adjust the following parameters:

OverPress Set [SET–39]:

Disable, OP Trip, or OP Auto Reset.

•

When enabled, if PID Feedback exceeds OverPress Level [SET–40], the VFD trips on Overpressure fault.

•

If setting is OP Trip, manual or remote reset is required. If Reset Restart [VFD–36] is enabled and a run
command is present, the VFD will restart when reset.

•

If setting is OP Auto Reset, the VFD will restart when PID feedback falls below Wake-Up Level [SET–31]
and a run command is still present.

OverPress Level [SET–40]:

Overpressure trigger level in PID feedback units, 0.0 to SET-20 (Unit) PID F/B

Max.

«
...
75
76
77
78
79
...
»

Содержание Cerus X-Drive





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cerus X-Drive

Бренд: ABB Страницы: 2

CRUSADER ONE 72H-033

Бренд: BMG Страницы: 3

encoTRive MD-025-CO-C Series

Бренд: TR-Electronic Страницы: 260

Бренд: RHINO MOTION CONTROLS Страницы: 10

Бренд: Newport Страницы: 41

Бренд: JVC Страницы: 29

Бренд: Shugart Страницы: 32

Бренд: STG-BEIKIRCH Страницы: 27

PowerFlex 755TM

Бренд: Rockwell Automation Страницы: 120

Бренд: Metronix Страницы: 95

PullMaster PH136

Бренд: Dover Страницы: 33

Бренд: ZIEHL-ABEGG Страницы: 28

Бренд: Bedford Страницы: 116

Бренд: Malmbergs Страницы: 8

Бренд: Vacon Страницы: 28

Бренд: SMS Страницы: 75

Бренд: Nakanishi Страницы: 9

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды