Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 156

background image

PHYSICAL INSTALLATION

Environmental Requirements

17

PHYSICAL INSTALLATION

Environmental Requirements

The VFD must be installed and used in a controlled environment that meets the following requirements:

The drive electronics are air-cooled. Provide
enough clearance for airflow around the VFD. See
minimum mounting clearance table below for dif

-

ferent VFD frame sizes.
Mount VFD vertically (top up) for proper heat dis

-

sipation.
Do not mount VFD in direct sunlight or near other
heat sources.
Do not block cooling vents or airflow with any
panel components or wires. Prevent debris from
adhering to the heat sink.

*

For frames sizes D, E, & F, install a metal separator between side-by-side drives. Barrier depth must match the VFD

depth.

Risk of damage to VFD

,

or malfunction can occur due to improper handling,

installation, or environment.

•

Do not mount VFD on equipment with excessive vibration.

•

Install in a location where temperature is within the range of product rating.

•

Do not mount VFD in direct sunlight or near other heat sources.

•

The VFD should be mounted in a Pollution Degree 2 environment. If VFD will be installed in an envi

-

ronment with a high probability of dust, metallic particles, mists, corrosive gas or other contami

-

nants, the VFD must be mounted inside an appropriate electrical enclosure with proper NEMA, UL
Type, or IP rating and adequate cooling.

•

When two or more VFDs are installed in a ventilated enclosure, the cooling system should provide
adequate airflow for all the VFDs. Do not install VFD above another heat source (another VFD,
inductive reactors, etc.).

Ambient Temperature

50 °C (122 °F) UL Open Type/IP20 (Top cover must be removed.)

40 °C (104 °F) in NEMA 1 / UL Type 1 / IP20 enclosure.

Location

Pollution Degree 2 Environment.

Altitude

1000m (3281 ft) above sea level. De-rate current 1% per 100 m (328 ft) from 1000 to 2000 m (3281-

6562ft). Consult Technical Support for installations above 2000 m.

Relative Humidity

95% Maximum relative humidity (non-condensing)

Vibration

1.0mm, peak to peak value range from 2 Hz to 13.2 Hz

0.7G-1.0G range from 13.2 Hz to 55 Hz

1.0G range from 55 Hz to 512 Hz.

A

A

B

B

C

D

Frame Size

A

B

C

*

D

A, B, & C

60 mm/2.4 in.

30 mm/1.2 in.

30 mm/1.2 in.

0 mm/0.0 in.

D, E, & F

100 mm/3.9 in.

50 mm/2.0 in.

100 mm/3.9 in. total 0 mm/0.0 in.

G

200 mm/7.9 in.

100 mm/3.9 in.

200 mm/7.9 in.

0 mm/0.0 in.

H

350 mm/ 13.8 in.

0 mm/0.0 in.

0 mm/0.0 in.

200 mm/7.9 in.

«
...
15
16
17
18
19
...
»

Содержание Cerus X-Drive





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cerus X-Drive

Бренд: Labelmate Страницы: 83

BHSS-1000W-PARA

Бренд: Bholanath Страницы: 22

Бренд: Veichi Страницы: 32

Бренд: LEGRAND Страницы: 8

Бренд: DVS Страницы: 16

Бренд: Unimotion Страницы: 22

Super-writemaster SH-S203N

Бренд: Samsung Страницы: 2

Super-writemaster SH-S203D

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 10

Бренд: Samsung Страницы: 15

SE-S084C - DVD±RW / DVD-RAM Drive

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 25

writemaster SE-S164L

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 25

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды