Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 132

Страница: 132 / 156

PARAMETER REFERENCE TABLES

Parameter Descriptions > COMM Menu

132

Parameter Descriptions > COMM Menu

AR = Adjustable while running.

PROT-45 1069 Y Fan Control

0_At Power-Up

1_Delayed Stop

2_During Run

3_By Temperature

4_Disabled

Determines operation of fan. Recommend not to set to 4-Disabled since

this will reduce performance of drive.

PROT-46 1070 Y Last Flt Freq

0.0 to SET-14 Hz

Output frequency at last fault (Read Only)

PROT-47 1071 Y Last Flt IGBTT

-3277 to 3276.7 °C

IGBT temperature at last fault (Read Only)

PROT-48 1072 Y Last Flt Cap T

-3277 to 3276.7 °C

Capacitance temperature at last fault (Read Only)

PROT-49 1073 Y Last Flt MFI

(Read Only)

Status of Multi-function input terminals at last fault

PROT-50 1074 Y Last Flt MFO

(Read Only)

Status of Multi-function output terminals at last fault

PROT-51 1075 Y 1st Fault

(Read Only)

First register of fault listing.

PROT-52 1076 Y 2nd Fault

(Read Only)

Second register of fault listing.

PROT-53 1077 Y 3rd Fault

(Read Only)

Third register of fault listing.

PROT-54 1078 Y 4th Fault

(Read Only)

Fourth register of fault listing.

PROT-55 1079 Y 5th Fault

(Read Only)

Fifth register of fault listing.

PROT-56 1080 Y 6th Fault

(Read Only)

Sixth register of fault listing.

PROT-57 1081 Y ULD Min Torque 5% to SET-42

Sets minimum torque level % at 0Hz when using Underload Torque.

PROT-58 1082 Y HLD Min Torque PROT-57 to SET-48

Sets minimum torque level % at 0Hz when using High load Torque.

CODE

Mod

Bus AR Display Name

Range

Description

CODE

Mod

Bus AR Display Name

Range

Description

Comm-00 1280 Y COM1 Address

1 to 254

RS485 address of VFD.

Comm-01 1281 Y COM1 Speed

4.8 to 115.2 Kbps

RS485 baud rate. All devices on RS485 communication must have the

same baud rate.

Comm-02 1282 Y COM1 Loss

0_Alarm and Run

1_Alarm_Decel

2_Alarm_Coast

3_Disable

Select operation when communication is lost.

Comm-03 1283 Y COM1 Loss Delay 0.0 to 100 Sec

Duration of communication loss before initiating operation.

Comm-04 1284 Y COM1 Protocol

1_7, N, 2 for ASCII

2_7, E, 1 for ASCII

3_7, O, 1 for ASCII

4_7, E, 2 for ASCII

5_7, O, 2 for ASCII

6_8, N, 1 for ASCII

7_8, N, 2 for ASCII

8_8, E, 1 for ASCII

9_8, O, 1 for ASCII

10_8, E, 2 for ASCII

11_8, O, 2 for ASCII

12_8, N, 1 for RTU

13_8, N, 2 for RTU

14_8, E, 1 for RTU

15_8, O, 1 for RTU

16_8, E, 2 for RTU

17_8, O, 2 for RTU

RS485 Protocol: Data Bits - Parity - Stop Bits - Message Format

Comm-05 1285 Y Response Delay 0.0 to 200 ms

Duration VFD waits before responding to received communication.

Comm-06 1286 N Main Frequency 0.0 to 599 Hz

When Auto Speed Ref [SET-07] is set to RS485 Interface, the last fre

quency command is stored in this parameter. After rebooting from an

abnormal turn-off or momentary power loss, the VFD will continue opera

tion with last frequency.

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды