7
6
MAINTENANCE
- Regular maintenance of the clippers’ blades will keep the appliance in an optimum conditions.
- Make sure that the appliance is switched off and unplugged.
- Remove the guide comb and clean it using the cleaning brush provided.
- Brush the blades carefully using the cleaning brush to remove any hair.
- Turn your clippers on and carefully add a few drops of lubricating oil to the blades. Wait a few seconds then turn the
clippers off and remove any excess oil using a dry cloth.
- Only use the oil supplied in the kit: this has been specially formulated for the clippers.
REMOVING THE RECHARGEABLE BATTERY
Note: we advise that you have the rechargeable battery removed by a professional.
Only remove the rechargeable battery when you are intending to discard the appliance. Unplug the appliance from the
mains. Make sure that the battery is fully discharged when you remove it.
1. Check if there are screws in the front or back of the appliance. If there are, remove them.
2. Remove the appliance’s front and/or rear panel using a screwdriver.
3. If necessary, remove the screws and/or additional parts until you can see the circuit board with the rechargeable
battery. If necessary, cut the wires to separate the circuit board and the rechargeable battery from the appliance.
This symbol, shown on the product or its packaging indicates that this product complies with European directive
2012/19/EU and that it must not be discarded with household waste. It must be taken to a suitable collection point for the
recycling of electrical and electronic equipment. By making sure that this product is disposed of properly, you will help
to prevent any potentially-negative consequences for the environment and human health. Recycling helps to conserve
natural resources.
This symbol means hart the product contains an integrated rechargeable battery which must not be discarded with
household waste (European directive 2013/56/EU). The rechargeable battery contains substances which may be dan-
gerous to the environment. Always remove the battery before discarding the appliance or take it somewhere intended
for this purpose. Dispose of the used battery appropriately. If you are unable to remove the battery, you can take the
appliance to an approved service centre.
CHARGING THE CLIPPERS
- Charge the clippers fully before the first use and after a long period of disuse.
- While charging, the charging light is red.
- It takes 8 hours to charge the appliance fully and it then has a battery life of approx. 45 minutes.
- Plug the small plug into the charging base.
- Plug the adapter into the mains.
- Place the appliance on the charging base.
Once charging is complete, unplug the adaptor from the wall socket.
OPTIMISING THE RECHARGEABLE BATTERY’S LIFE
Once the appliance has been charged for the first time, we recommend using it until the battery is discharged com-
pletely. Allow the appliance to operate until the motor comes to a stop. Then recharge the battery. Perform this operation
at least twice a year.
TO BEGIN
- Make sure that the appliance is switched off before removing or installing the head or before attaching the guide
comb.
- To attach the head, adjust the bottom of the accessory on the appliance and interlock until you hear a click.
- To remove the head, hold the appliance’s handle with one hand and remove the head with the other hand by pushing
it upwards.
- If you are using the clippers for the first time, please be careful: do not make any fast movements; uniform movements
are recommended.
USING THE GUIDE COMB
- The cutting height indicated on the guide comb is given in millimetres and corresponds to the hair length after cutting.
- Tip: start by cutting using a high cutting height and gradually reduce the cutting height until you achieve the desired
result. The guide comb guarantees a uniform cutting height.
- IMPORTANT: always position the guide comb BEFORE turning the clippers on and always turn the clippers off before
removing the guide comb.
- Place the guide comb on the edges of the clippers’ blades then push on the back of the guide comb until you hear a
click. To remove, detach the back of the guide comb then remove it.
TO THIN OUT AND TAPER YOUR BEARD/MOUSTACHE
- Attach the adjustable guide comb to the trimmer’s blade and select the desired length by sliding the guide comb
upwards or downwards.
- Once you have set the adjustable guide comb to the desired length, switch the trimmer on.
- Place the guide comb’s flat top against the skin.
- Complete movements towards the edge of your beard/moustache to size it according to your preferences in the
different areas of your face and movements towards the outside of your beard at neck level.
TRIMMING YOUR SIDEBURNS
Start with the edges of the sideburns and, with the blades of the trimmer pushed gently against your skin, more the
appliance towards the outer edges of the sideburns to size them according to your preferences.
TO TRIM YOUR NECK
Note: You will need a mirror to do this if you are alone.
- Remove the adjustable guide comb from the clippers. Use your fingers to remove the hair from the neck. Your index
finger should cover the roots of the hair you want to remove to prevent any accidental cutting with the trimmer.
- With your other hand, hold the trimmer at the base of your neck with the blades facing upwards and move the trimmer
up along the length of your neck until it comes into contact with your finger covering the roots of the hair at the base
of your head.
Make sure that you move the appliance slowly when doing this and hold the roots of the hair at the base of your head
away from the trimmer.
TIPS FOR ACHIEVING THE BEST RESULTS
Beard, moustache and sideburn hair must be dry. Avoid applying lotions before using the trimmer.
