manualshive.com logo in svg

Framery Q Maggie, Руководство по установке

Поделиться
Скачать
Framery Q Maggie Скачать руководство пользователя страница 11

Framery Q Meeting Maggie

Disconnect the power cord from the power outlet before starting any

cleaning, maintenance, or disassembly procedures.
The power cord serves as a power disconnect device for pluggable

equipment. The power outlet shall be located near the equipment and shall

be easily accessible.

WARNING!
To reduce the risk of burns, fire, electric shock, or injury to persons,

obey the following:

Connect the power cord to a properly grounded outlet only.

This product is for use on a nominal 120-volt circuit and has a grounding

plug that looks like the plug illustrated in the figure below. Make sure that the

product is connected to an outlet having the same configuration as the plug.

No adapter should be used with this product.

Keep the power cord of the product away from heated surfaces.

Do not use the pod if you notice any defects or damage to the electrical

equipment.

Do not connect any extension cords to the power outlet(s) of the product.

2.7.3 Fire safety

The fire load for the Framery Q is approx. 5200 MJ.

WARNING!
To reduce the risk of burns, fire, electric shock, or injury to persons,

obey the following:

Installation instructions
[email protected]

11

Содержание Maggie













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды