22
U35 FPI Direct Vent Gas Insert
MAINTENANCE
GENERAL VENT
MAINTENANCE
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
1)
Check the Venting System for corrosion in areas
that are exposed to the elements. These will
appear as rust spots or streaks, and in extreme
cases, holes. These components should be
replaced immediately.
2)
Remove the Termination Cap, and shine a
fl
ashlight down the Vent. Remove any bird
nests, or other foreign material.
3)
Check for evidences of excessive condensation,
such as water droplets forming in the inner
liner, and subsequently dripping out the joints,
Continuous condensation can cause corrosion
of caps, pipe, and
fi
ttings. It may be caused
by having excessive lateral runs, too many
elbows, and exterior portions of the system
being exposed to cold weather.
4)
Inspect joints, to verify that no pipe sections or
fi
ttings have been disturbed, and consequently
loosened. Also check mechanical supports such
as Wall Straps, or plumbers' tape for rigidity.
LOG REPLACEMENT
The unit should never be used with broken logs. Turn
off the gas valve and allow the unit to cool before
opening door to carefully remove the logs. The pilot
light generates enough heat to burn someone. If
for any reason a log should need replacement, you
must use the proper replacement log. The position
of these logs must be as shown in the diagram
under Log Installation.
NOTE: Improper positioning of logs may create
carbon build-up and will alter the unit’s performance
which is not covered under warranty.
GLASS GASKET
If the glass gasket requires replacement use
glass gasket (Part # 936-265) for the Bay Front
and a tadpole gasket for the Flush Front (Part #
936-155).
STEEL OR GOLD TRIM
The steel or 24 carat gold plated
fi
nish on the
trim requires little maintenance, and need only be
cleaned with a damp cloth. DO NOT use abrasive
materials or chemical cleaners, as they may harm
the
fi
nish and void the warranty.
Top View of pilot
fl
ame
Top View of pilot
fl
ame
Incorrect
fl
ame pattern will have small, probably
yellow
fl
ames, not coming into proper contact
with the rear of the burner or thermopile.
6)
Each time the appliance is lit, it may cause
condensation and fog the glass. This
condensation and fog is normal and will
disappear in a few minutes as the glass
heats up.
Never operate the appliance without the
glass properly secured in place or with
the door open.
7)
Do not use this appliance if any part has
been under water. Immediately call a
quali
fi
ed service technician to inspect the
appliance and to replace nay part of the
control system and any gas control which
has been under water.
8)
Periodically check the pilot
fl
ames. Correct
fl
ame pattern has three strong blue
fl
ames: 1
fl
owing around the thermopile and 1 around
the thermocouple, and 1
fl
owing across the
rear of the burner (it does not have to be
touching the burner).
Note: If
you have an incorrect
fl
ame pattern,
contact your FPI dealer for further
instructions.
C L O T H I N G O R O T H E R
FLAMMABLE MATERIAL SHOULD
NOT BE PLACED ON OR NEAR
THE APPLIANCE.
WARNING: CHILDREN AND
ADULTS SHOULD BE ALERTED
TO THE HAZARDS OF HIGH
SURFACE TEMPERATURE AND
SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD
BE CAREFULLY SUPERVISED
WHEN THEY ARE IN THE SAME
ROOM AS THE APPLIANCE.
CAUTION: ANY SAFETY SCREEN
OR GUARD REMOVED FOR
SERVICING AN APPLIANCE
MUST BE REPLACED PRIOR TO
OPERATING THE APPLIANCE.
MAINTENANCE
INSTRUCTIONS
1)
Always turn the gas valve to off before
cleaning. For relighting, refer to lighting
instructions. Keep the burner and control
compartment clean by brushing and
vacuuming at least once a year.
When cleaning the logs, use a clean soft
paint brush as the logs are fragile and easily
damaged.
2)
Clean (never when unit is hot) appliance,
door and louvers with a damp cloth. Never
use an abrasive cleaner. The gold louvers
(and optional gold door) may be scratched
if abrasives are used to clean them.
The heater is
fi
nished in a heat resistant
paint and should only be re
fi
nished with
heat resistant paint (not with wall paint).
FPI uses StoveBrite Paint - Metallic Black
#6309.
3)
Make a periodic check of burner for proper
position and condition. Visually check the
fl
ame of the burner periodically, making sure
the
fl
ames are steady; not lifting or
fl
oating.
If there is a problem, call a quali
fi
ed service
person.
4)
The appliance and venting system must be
inspected before use, and at least annually,
by a quali
fi
ed
fi
eld service person, to ensure
that the
fl
ow of combustion and ventilation
air is not obstructed.
During the annual service call, the burners
should be removed from the burner tray
and cleaned. Replace the embers but do
not block the pilot.
5)
Keep the area near the appliance clear and
free from combustible materials, gasoline
and other
fl
ammable vapours and liquids.
