FOURAUDIO PPA Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 37

FOURAUDIO PPA Series Скачать руководство пользователя страница 19

Date: 2017-06-28

PPA DSP amplifier user manual

19

Figure 8 PPA1600 / M-PRO2 location of speaker
outputs

7.2.

PPA1600 / Pascal® M-PRO Module

Use the following parts for the speaker output sockets:



Cable connector housing Molex 42021-2A (Farnell
1393363)



Cable connector pin Molex MLX 42024 (Farnell
2396371)

Please note:

The output connector ST500 is rotated by 180 degrees, thus the output of ST500 (Ch. 2) is inverted. This will
prevent pumping of the power supply. In order to have outputs of channel 1 and channel 2 in phase, the input of
channel 2 should be inverted

Table 2 PPA1600 / M-PRO2 speaker connection (ST300, ST500)

Connector

Pin

Description

ST300

1

CH1 OUT+

The amplified speaker signal of channel 1 is available on this pin

ST300

2

CH1 GND

This pin is used for the GND signal of the channel 1 speaker

ST500

1

CH2 GND

This pin is used for the GND signal of the channel 2 speaker

ST500

2

CH2 OUT+

The amplified speaker signal of channel 2 is available on this pin

«
...
17
18
19
20
21
...
»

Содержание PPA Series






































Отзывы:

Нет отзывов