HT-1002LCD-A
This unit is shipped from the factory with its internal battery fully charged; however, some
charge may be lost during shipping. Therefore, it is recommended to recharge the battery
prior to initial use.
Simply plug the unit into an appropriate AC outlet, and allow it to charge to maximum
capacity for 6 hours.
Important safety instructions
SAFE HANDLING OF BATTERIES
Attention: Risk of electric shock
1. Introduction
CAUTION!
The voltage used by this UPS may be hazardous. The unit contains no user serviceable parts;
do not attempt to disassemble the unit. Only factory service technicians can perform
maintenance on the unit.
This unit is intended for installation in a controlled environment (temperature-controlled
indoor area location, free of conductive contaminants). Avoid installing the UPS where there
is standing or running water, or excessive humidity.
To reduce the risk of overheating, do not cover the cooling vents. Avoid exposing the UPS to
direct sunlight or installing the unit near heat-emitting appliances, such as electric heaters
or furnaces.
Do not connect non-computer related peripheral devices, such as medical devices,
life-support equipment, microwave ovens, or vacuum cleaners to the UPS.
Do not connect any power strip or surge suppressor to the UPS.
Do not plug the UPS AC input power cord into its own output.
Do not allow any kind of liquid or foreign object to enter this UPS unit. Do not place
beverages or any other containers with liquid on or nearby the unit.
During the installation of this equipment, make sure that the sum of the leakage currents of
the UPS and the connected loads shall not exceed 3.5mA.
In case of emergency, turn the power switch “off” and disconnect the power cord from the
AC mains outlet.
Unplug the UPS before cleaning, and do not use liquid or spray detergents.
Never try to open or mutilate a battery. Released electrolyte is harmful to the skin and eyes,
and also can be toxic.
Servicing of batteries should be performed or supervised by experts who possess the
knowledge to closely follow all required precautions.
When replacing the battery, make sure to use the same type and number of sealed lead-acid
batteries specified.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
·
A battery can present the risk of short-circuit current and electrical shock. The
following precautions should be taken:
Attention:
·
·
·
Potentially hazardous voltages from the battery can still be present even after disconnecting
the UPS from the AC mains. Therefore, the positive and negative terminals of the battery shall
be disconnected prior to performing any maintenance or repair inside the unit.
The UPS contains internal 12VDC, sealed, lead-acid batteries.
Do not dispose of batteries in a fire. Batteries may explode if exposed to high temperatures.
Thank you for purchasing the HT-752LCD-A / HT-1002LCD-A UPS system from Forza. To
enjoy all the features and benefits of this unit, we encourage you to read this manual and
follow the installation and operation procedure thoroughly.
2. Package content
2.1 Inspection
Upon opening the box, make sure the following items are included.
1) Remove watches, rings, or other metal objects from your hand.
2) Use tools with insulated handles.
3) Wear rubber gloves and boots.
4) Do not place tools or metal parts on the top of batteries.
5) Disconnect charging source prior to connecting or disconnecting battery terminals.
Remove the UPS from its package and look for damages that may have occurred during
shipping. If any damage is discovered, repack the unit and return it to the place of purchase.
HT-752LCD-A / HT-1002LCD-A
3. Product description
4. Installation and operation
4.1 Choose a location
Install the UPS unit in any protected environment that provides adequate airflow around the
unit, and free from excessive dust, corrosive fumes and conductive contaminants. Do not
operate your UPS in an environment where the ambient temperature or humidity is high.
4.2 Charge the UPS
NOTE: Make sure that the UPS is powered on to protect all important devices from data
loss during power failure.
·
·
4.3 Connection of the loads
Connect one device into each power receptacle provided on top of the UPS.
Plug sensitive equipment into the battery backup outlets.
Battery power is automatically provided to the loads in case of a power outage.
·
·
NEVER connect a laser printer or scanner to the UPS with other computer equipment. A
laser printer or plotter periodically draws significantly more power than when idle, and may
overload the UPS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
LCD display
Main power button
AC power cord
Surge protected outlets
Battery backup and AVR protected outlets
Telephone/modem/network protection
USB charging ports
Coaxial line jacks
Battery compartment
User guide
UPS unit
Warranty certificate
Top/side panel
Bottom panel
6 hours
7
6
8
2
5
3
1
4
9
Computer
Monitor
HT-1002LCD-A
