Forum 691250-Z-BC Скачать руководство пользователя страница 31

Страница: 31 / 66

Operation Maintenance Manual

07-2018

PN 691250-Z-BC-D - Revision: 04

Solid Body Elevator

RT/

STA

3.4

Setup

DANGER

Suspended load!

The falling load can cause severe, even
lethal injuries.

» NEVER stand under suspended

loads.

» NEVER stand in the swing area of

suspended loads.

WARNING

Pinching/crushing hazard from
lowering!

Severe pinching/crushing up to loss of
limbs.

» NEVER step over edge of rotary

table with feet.

WARNING

Danger of pinching/crushing
hands!

This indicates injury risks from moving
parts, which pose a hazard of pinching
or crushing hands.

WEAR PROTECTIVE HELMET!

WEAR PROTECTIVE GLOVES!

WEAR SAFETY SHOES!

The Solid Body Elevator is completely preassembled before
shipment, so that it can be installed immediately after
unpacking at the installation site.

Preparation

1. Remove the transport packaging and transport

aids from the Solid Body Elevator and position the
Solid Body Elevator on the rig, near the
Elevator-Links.

Procedure

1. Place the Solid Body Elevator on a plane surface and

open the Link Adapter

by removing the upper Link

Block screw, washer and cotter pin.

Fig. 17: Step I

2. Move the Link Block

upwards.

3. Carefully guide the Elevator-Link to the

Solid Body Elevator

. Make sure, the Elevator-Link is

mounted and placed correctly.

Fig. 18: Step II

WARNING

Pinching and crushing!

The Elevator-Links must be handled and guided
from the outside of the Lifting ear opening of the
Solid Body Elevator. Use ropes to adjust the Elevator-Links.

4. Move the Link Block upwards. Secure the Link Block

with screw, washer and cotter pin

Fig. 19: Step III

5. Repeat step 2 to 5 or the second Elevator-Link.

Removal

1. Perform installation rocedure in reversed order.

Содержание 691250-Z-BC



































































Результаты поиска

Содержание 691250-Z-BC

Отзывы:

Forum 691250-Z-BC, Руководство по эксплуатации, Страница: 31 / 66

Результаты поиска

Содержание 691250-Z-BC

Отзывы: