QuickStart Guide
© Copyright 2010 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class B Part 15, / CE Mark
7 August 2010
FortiAP-210B/220B
01-420-127515-20100702
Visit these links for more information and documentation for your Fortinet product:
Technical Documentation -
http://docs.fortinet.com
Fortinet Knowledge Center -
http://kb.fortinet.com
Technical Support -
http://support.fortinet.com
Training Services -
http://campus.training.fortinet.com
If the FortiGate wireless controller’s IP address cannot be determined from the
methods above or if the network uses static IP addresses, do the following:
1. Connect the FortiAP to a separate private switch or hub or directly connect
to your computer via a cross-over cable.
2. Change your computer’s IP address to 192.168.1.3
3. Telnet to IP address 192.168.1.2. This IP address is overwritten if the
FortiAP is connected to a DHCP environment. Ensure that FortiAP is in a
private network with no DHCP server for the static IP address to be acces-
sible.
4. Login with username:
admin
and no password.
5. Type the following commands to enter static IP address for Access Point.
netmask & gateway information for your network. Replace zzz with the IP
address of the FortiGate Wireless Controller.
cfg –a AP_IPADDR=”xxx.xxx.xxx.xx”
cfg –a AP_NETMASK=”255.255.255.0”
cfg –a IPGW=”yyy.yyy.yyy.yyy”
cfg –a AC_IPADDR_1=”zzz.zzz.zzz.zzz”
6. Save the configuration by typing the following command:
cfg –c .
Unplug the FortiAP and plug it back in order for the configura-
tion to take effect.
7. Move the FortiAP to the intended deployment location and connect the
Ethernet cable as described in the Connecting section.
8. In FortiGate controller Web Config, go to
Wireless Controller > Configura-
tion > Access Point
. A successfully discovered unit displays a half-filled
circle symbol.
9. Select the Access Point and click Edit.
10. In the Admin field, select Enable.
11. In the AP Profile field, select a profile from the list and click OK.
The configuration is downloaded from the FortiGate unit to the FortiAP and
the Wireless LED lights up.
Note:
FortiGate Low encryption units must be matched up with Low Encryp tion
Access Points.
Power Required
Adaptor Input 100-240V~ 50/60Hz 0.6A
Output: 12V DC 1.5A –center positive
Ports
1 x 10/100/1000 PoE (IEEE 802.3af)
1 Console127515
1 USB 2.0
Number of radios
FortiAP-210B — 1
FortiAP-220B — 2
WiFi
802.11 a, b, g, n
Mount
Wall or ceiling
Configuring continued...
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
: Any changes or modifications not expressly approved by the party responsible for com-
pliance could void the user’s authority to operate this equipment.
For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation.
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmit-
ter.
The availability of some specific channels and/or operational frequency bands are country dependent
and are firmware programmed at the factory to match the intended destination. The firmware setting is
not accessible by the end user.
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Règlement d’Industry Canada
Les conditions de fonctionnement sont sujettes à deux conditions:
1) Ce périphérique ne doit pas causer d’interférence et.
2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le
bon fonctionnement de ce périphérique.
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Caution:
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interfer-
ence to co-channel mobile satellite systems.
