Förster-Technik TAP5-VS2-50 Скачать руководство пользователя страница 108

Страница: 108 / 130

108

Faults and warnings

9.5

Diagnosis

The

Diagnostics

menu helps you to find faults in the event of technical problems. You can

reach this menu via

. A diagnosis can be performed for the following parts of the automatic

feeder:

•

Valves

•

Motors

•

Heating system

•

Sensors

•

Calibration scales

•

Stations

•

Check

•

Version

•

Setup

•

Software

•

Remote maintenance

9.5.1

Checking valves/motors

In this menu, you check actuators (valves and motors) and their actuation.

9.5.1.1

Valves

Check the valves as follows:

1. Navigate via

> Diagnostics

to switch to the

Valves

sub-menu.

2. Confirm

Bo. water open?

by choosing

, to open the water valve. The valve remains

open as long as you hold the key down.

3. In the

Gully valve 2

menu, press

. A new menu in which you can check the gully valve

will open.

3.1.

Confirm

Water to the gully

by choosing

, to rotate the valve towards the gully, or

confirm

Water to the mixer

by choosing

, to rotate the valve towards the gully.

The check (



) behind the selected line show the last position to which the valve was

switched.

3.2.

In the

Boiler water: open?

Menu, press

, until the mixer is filled with water.

3.3.

Confirm

Water circulation

by choosing

, to pump the water around the circuit or

into the gully. The direction can be detected at



4. Confirm

Mixer drain: open?

by choosing

, to open the mixer drain valve. The valve re-

mains open as long as you hold down

5. Check that the valve opens.

Содержание TAP5-VS2-50



































































































































Результаты поиска

Содержание TAP5-VS2-50

Отзывы:

Похожие инструкции для TAP5-VS2-50

Бренды по названию

Популярные бренды

Förster-Technik TAP5-VS2-50, Оригинальное сервисное руководство

Результаты поиска

Содержание TAP5-VS2-50

Отзывы:

Похожие инструкции для TAP5-VS2-50

Бренды по названию

Популярные бренды