background image

 
5. Loosen the screw on the small box (the screw is connected to the inside 

of the liner and can be screwed out from the inside of the liner) 

 

6. On the right side of the box, you can see two screws, screw out the two 

screws and open the small cover of the box. 

 

7. Remove the old tube, put the new tube back inside the small box, close 

the lid, and tighten the two screws on the lid. 
 

23A, 46A towel cabinet replacement lamp steps: 

1. Remove all the screws on the back panel and open the back panel. 

2. You can see the white cotton after opening the back panel. 

 

3. Take out the white cotton back, you can see the position of the lamp, as 

shown 

 

4. Unplug both lines 

 

                 Premium Hot Towel Warmer

Item #391442 • New Hudson, MI 48165

www.tngworldwide.com • 800.520.6000

Made in China • ©2020 TNG

Troubleshooting

1.   There is excessive moisture when the towel warmer is ON or the towels are heating up very 

slowly.

  •  Check to see that the towels are only slightly damp. Excess moisture and/or slow heating 

time may be a result of soaked towels.

2.  The door is not closing properly and/or steam is escaping

  •  Check that the silicone door seal is in place. Push into door groove to assure proper fit. 

Safety Precautions

Caution and proper procedures must be practiced at all times when using electrical appliances. 

Basic safety precautions should always be followed, including the following:

• Do not use appliance for other than intended use.

•  Do not place poisonous, flammable, explosive and evaporative chemicals into the towel 

warmer. 

• Do not touch hot surfaces. Use handle or knobs.

•  To protect against electrical shock, do not immerse cord, plugs or appliance in water or 

other liquid.

•  Unplug from outlet when not in use and before cleaning. Cool the machine before 

maintenance.

•  Do not operate any appliance with a damaged cord or plug or after the appliance 

malfunctions or has been damaged in any manner. If the product is defective, stop using it at 

once and contact supplier for service. 

• Do not use outdoors. This appliance is intended for indoor use only.

• Do not let cord hang over edge of table or counter, or touch hot surfaces.

• Close supervision is necessary when any appliance is used by or near children.

• Do not leave the appliance unattended when switched on.

• Extreme caution must be used when moving an appliance containing hot liquids.

• The temperature of accessible surfaces may be high when the appliance is operating.

•  If using an extension cord, the marked electrical rating of the extension cord should be at 

least as great as the electrical rating of the appliance.

Internal surfaces, wire baskets, towels and steam may be hot. Use with extreme caution 
when removing hot towels or baskets. Always use protective heat-resistant gloves or 
mitts to avoid steam or other burns. Ignoring the warnings may result in harm or serious 
injury.

 

Premium 

Hot Towel Warmer

Replacing the UV Bulb 

continued

8.  On the right side of the box, you can see two screws, screw out the two screws and open 

the small cover of the box. See Fig. 5a & 5b.

  

9.  Remove the faulty UV bulb. Insert a new UV bulb (Replacement bulb Item #391445) back 

inside the small box, close the lid, and tighten the two screws on the lid. See Fig. 6a & 6b.

  

10. Reattach both lines and tighten the screws of the UV box. See Fig. 7a & 7b.

11. Replace environmentally friendly cotton and reattach back panel.

 
5. Loosen the screw on the small box (the screw is connected to the inside 

of the liner and can be screwed out from the inside of the liner) 

 

6. On the right side of the box, you can see two screws, screw out the two 

screws and open the small cover of the box. 

 

7. Remove the old tube, put the new tube back inside the small box, close 

the lid, and tighten the two screws on the lid. 
 

 

8. Tighten the screws of the UV box 
9. Install environmentally friendly cotton and backboard 

 

 

8. Tighten the screws of the UV box 
9. Install environmentally friendly cotton and backboard 

 

 
5. Loosen the screw on the small box (the screw is connected to the inside 

of the liner and can be screwed out from the inside of the liner) 

 

6. On the right side of the box, you can see two screws, screw out the two 

screws and open the small cover of the box. 

 

7. Remove the old tube, put the new tube back inside the small box, close 

the lid, and tighten the two screws on the lid. 
 

Fig. 5a

Fig. 6a

Fig. 5b

Fig. 6b

Fig. 7a

Fig. 7b

Отзывы: