formlabs Fuse 1 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 64

formlabs Fuse 1 Скачать руководство пользователя страница 30

28

4.8.3

Powder credit notifications

The printer reminds you of low powder credit
over time, indicating that you may only have
enough powder on hand for several more
prints. Upon starting a print, the printer warns
you if your credit is low.

•

If the printer does not have sufficient
powder credits for the current print job,
the printer notifies you and does not start
the print job. Load additional powder credit
onto the printer and restart the print job.

•

After a print completes, the printer
notifies you if your powder credit total is
low. Check the

Printer Status

screen to

confirm there is enough powder credit
registered to the printer to complete
your upcoming prints. If not, you will be
unable to start the next print until sufficient
powder credits are registered to the
printer. Register additional powder credits
or order additional powder.

4.9

Preparing the optical cleaning kit

The Fuse 1 comes with three push-top dispensers for the Alconox, distilled water, and ethanol
used to clean the optical cassette. Each dispenser is dedicated to one cleaning agent. The
three cleaning agents must be purchased separately.

Below is a list of Formlabs-approved distributors of the cleaning consumables
validated for use with the Fuse 1. Do not use swabs, pre-moistened or dry wipes,
surfactants, denaturants, or any other tool, chemical, or cleaning agent that is not
explicitly recommended by Formlabs or a certified service provider.

Item

Sources

Alconox (1104-1)

Distilled water

Ethanol

PEC*PADs

Polyester cloth swabs (TX714A)

4.9.1

Mixing Alconox

Alconox is a powder and must be mixed with distilled water in order to be an effective
detergent for cleaning the optical cassette.

NOTICE

«
...
28
29
30
31
32
...
»

Содержание Fuse 1

































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды