background image

 

FORM FIT 

HOOD PROTECTOR 

 

   

Toyota Yaris 2006 - 

 

 

 

 

 

 

 

 

       

       

HD 20S 06

 

Hardware Kit

 

Tools Required 

 

3 – Large Bumpons               

             1 – Phillips Screwdriver #2 

4 – 3M Anti-Abrasion Film Pad 

             1 – Tape Measure 

4 – Clip Bodies 

             1 – Grease Pencil 

4 – Pins 

            4 – ‘L’ Brackets 

4 – #6 x 5/8” Flat Head Screws 

*

Note: This Part has 3 Supporting Clips- already installed on the protector 

               

 

 

Installation      

1. 

Be sure that the hood is clean and dry inside and out.   

2. 

Position the bumpons on the hood as shown in illustration #1.  

Attention: The bumpons must be installed on the hood not the protector!!!! 

If the 

bumpons are installed on the protector, they will wear through the paint. 

3. 

Open the hood of the vehicle. 

4. 

Using a tape measure and grease pencil, measure and mark the center of the leading edge of the hood. 

5. 

Center the protector on the hood by aligning the notch on the leading edge of the protector with the mark determined in previous step. 

6. 

Work from left to right pushing each of the protector supporting clips (already attached to protector) over the edge of the hood.  Be sure the protector clips 
are fully seated against the hood edge. 

7. 

Peel and fold an anti-abrasion film pad in half over the edge of the hood, underneath each of the two (2) inner holes in the protector. 

See Illustration #1 

and #2 – Step #7.

 

8a)   Place a clip over each of the anti-abrasion film pads on the edge of the hood as shown in 

Illustration #2 – Step #8a

  b)   Insert a pin through the protector into each of the clips. 

See Illustration #2 – Step #8b. 

  c)   Insert a #6 x 5/8’’ screw through an ‘L’- bracket and into the clip.  

See Illustration #2 – Step #8c & 8d. 

 

  d)   Make sure all the components are well seated together; the protector is centered on the hood, and then tighten the screws into the clips.  
9. 

Repeat step #7 and #8 for the other two (2) holes. 

10.  On some vehicles it may be necessary to adjust the hood bumpers and/or latch for proper clearance. 

Note: Do not pull on the protector when opening or closing the hood. 

Care Instruction                         

Clean the protector with a mild soap and water solution or plastic cleaner only.  Do not use chemicals or solvents.

  Periodically check to make 

sure that the hardware is in place and that the protector is secure.  

Avoid using automatic car washes.

  Do not pull on the protector when opening or 

closing the hood. 

Illustration #1: Bumpon and Clip Location 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

360mm                   360mm 

 

Illustration #2: Clip Configuration 

 

 

 

 

 

 

 

 

 

 

Thank you for purchasing a 

form fit

 hood protector.  Retain this sheet for care instructions and kit information. 

 

Made 

in 

Canada 

           

Rev2.100129 

 

   

 

 

 

Step #8b 

Step #7 

Step #8a 

Step #8c & 8d 

- Patent No. 6,892,427

90mm     

90mm 

90mm    

Clips (Step #9) 

Clips (Step #7 & #8) 

Отзывы: