manualshive.com logo in svg

Forlinx SBC OKMX8MPQ-C, Руководство пользователя

Поделиться
Скачать
Forlinx SBC OKMX8MPQ-C Скачать руководство пользователя страница 36

36

36

SD: the development board takes TF card for system guiding, thus to install firmware for the board

by TF card

QSPI: system firmware boot from QSPI NorFlash.

Note:

The pulled-up voltage of BOOT signal is from VDD_3VS output from SoM.

3.4.4 Debug

There are 2 debug ports from SoM, UART2 is for A53 debug and UART4 is for M7 debug. It’s drawn out to one
USB port on carrier board by a USB to serial convert chip CH342F . To use debug port, please firstly install
CH342F driver(http://www.wch.cn/products/CH342.html). Then take USB to Type C cable to connect
development board P11 to USB port on PC, and in computer device management, it will generate 2 COM ports, A
port is for A53 debug and B port is for M7 debug.

Open debug terminal tool on PC, such as Putty, and set baud rate to 115200, data bit 8, no parity bit, stop bit 1,
choose correct COM port, and then power on development board to boot system, then we’ll see serial output
information.
Users can also take a UART convert cable to connect to P12 or P13.
Note:
1. We kindly suggest users preserve debug port when designing PCB;
2. The debug port on carrier board designed with anti-creep solution for users’ reference.

Содержание SBC OKMX8MPQ-C




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды