background image

V C M M   H A R D W A R E   M A N U A L  

 

 

 6 

Equipment Precautions  

The following warnings must be observed when using the VCMM. 

IMPORTANT SAFETY INSTRUCTIONS

 

 

WARNING: Failure to follow these instructions will increase the risk of personal injury.

 

 

Step 1:

 Read all instructions. 

Step 2:

 

DO NOT 

use the VCMM or its cables and probes for measurements greater than 60 

VDC, 30 VAC or 42 VAC  peak.  The accessories must only be used in circuits which are not 
connected to a mains voltage supply (measuring category 0 according to EN 61010-2-030:2010). 
The enclosed accessories must only be used with the VCMM, and at voltages below the voltage 
value as imprinted on the accessories. When combining accessories, it must be ensured that the 
lowest voltage value imprinted on the accessories is not exceeded. 

Step 3:

 

DO NOT 

remove the rubber end boots while using the VCMM unit. The rubber end boots 

serve as shock protection and include important VCMM port information symbols. 

Step 4:

 Care must be taken as burns can occur from touching hot parts or surfaces. 

Step 5:

 

DO NOT 

operate equipment if damage to unit or cable is suspected. 

Step 6:

 

DO NOT

 let cables hang over edge of table, bench or counter or come in contact with 

hot manifolds or moving fan blades. 

Step  7:

 

DO NOT

  place tools or test equipment on vehicle fenders or other places inside the 

engine compartment. 

Step  8:

  Let equipment cool completely before putting away. Loop cables  loosely around 

equipment when storing. 

Step 9:

 Adequate ventilation should be provided when working on internal combustion engines. 

Step 10:

 Keep hair, loose clothing, jewelry, fingers and all parts of body away from moving parts 

of the vehicle. 

Step  11:

  Use this equipment only as described in the manual. Use only manufacturer’s 

recommended attachments. 

Step 12:  ALWAYS WEAR SAFETY GLASSES WHEN USING GARAGE EQUIPMENT.

 

Everyday eyeglasses only have impact resistant lenses, they are 

NOT 

safety glasses. 

SAVE THESE INSTRUCTIONS 

Содержание VCMM





































Отзывы: