background image

FUEL FILTER/WATER SEPARATOR

Fuel Conditioner Module (FCM - E-Series)

The vehicle is equipped with a Fuel Conditioning Module (FCM) located
on the driver-side of the vehicle next to the transmission case.

Water should be drained from the
module assembly whenever the
warning light comes on. The WATER
IN FUEL light will come on when
approximately 0.2 pints (100 ml) of water accumulates in the module. If
water level is allowed to exceed this level, the water may be passed
through to the engine and may cause FIE (Fuel Injection Equipment)
damage.

Horizontal Fuel Conditioner Module (HFCM - F-Super Duty)

The vehicle is equipped with a Horizontal Fuel Conditioning Module
(HFCM) located on the frame-rail under the driver-side floorboard near
the transmission

Water should be drained from the
module assembly whenever the
warning light comes on. The WATER
IN FUEL light will come on when
approximately 0.13–0.16 pints (60–75 ml) of water accumulates in the
module. If water level is allowed to exceed this level, the water may be
passed through to the engine and may cause FIE (Fuel Injection
Equipment) damage.

DRAINING THE HFCM AND CHANGING THE ENGINE AND
VEHICLE FUEL FILTERS

Your vehicle is equipped with two fuel filters; one is mounted on top of
the engine.

On F-Super Duty,

the second filter, inside the HFCM, is

mounted inside the frame rail under the driver-side floorboard near the
transmission.

On E-Series,

the second filter, inside the FCM, is mounted

on the driver-side of the vehicle next to the transmission case.

On all

vehicles,

both filters should be replaced at the same time. Regular fuel

filter changes are an important part of engine maintenance; failing to
keep with the scheduled maintenance could lead to engine performance
issues and/or fuel injection system damage. Refer to the

Scheduled

maintenance guide

chapter of this supplement for more information.

Refer to

Motorcraft part numbers

later in this chapter for the fuel filter

replacement part number. This part number includes filters and seals for
both the engine-mounted and frame-mounted filters.

Maintenance and Specifications

40

2010 Econoline

(eco)

Supplement

(supplement)

, 1st Printing

USA

(fus)

Содержание 2010 Econoline









































































































Отзывы: