Ford 2010 Econoline страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 104

background image

STARTING THE ENGINE

Read all starting instructions carefully before you start your vehicle.

For temperatures below 32°F (0°C), the use of the correct grade engine
oil is essential for proper operation. Refer to

Engine oil specifications

in the

Maintenance and Specifications

chapter for more information.

Your vehicle may be equipped with a cold weather starting strategy that
prevents severe engine damage by assisting in engine lubrication
warm-up. In extremely cold ambient temperatures, this strategy activates
and prevents the accelerator pedal from being used for 30 seconds after
starting the vehicle. By not allowing the accelerator pedal to be used, the
engine oil is allowed to properly lubricate the bearings preventing engine
damage due to lack of proper lubrication. After the 30 second warm-up
period, the accelerator pedal will be operational again as long as the
pedal is not being pressed when the 30 second time limit expires. When
starting the engine in extremely cold temperatures (-15°F [–26°C]), it is
recommended to allow the engine to idle for several minutes before
driving the vehicle.

If your vehicle is equipped with a manual transmission,

make sure

the parking brake is fully set before you turn the key. Depress the clutch
pedal and place the gearshift in the neutral position. The clutch must be
fully depressed in order to operate the starter. Do not press the
accelerator during starting.

If your vehicle is equipped with an automatic transmission,

ensure

the gearshift lever is in P (Park) and the parking brake is fully set before
you turn the key. Do not press the accelerator during starting.

Engine-driven cooling fan (fan clutch)

Your vehicle is equipped with an engine driven cooling fan drive (also
called a fan clutch). This fan drive changes the fan speed to match the
vehicle’s changing cooling air flow requirements. Fan speed, fan noise
level and fuel consumption all will increase based on the driving
conditions that include trailer towing, hill climbing, heavy loads, high
speed and high ambient temperature, individually or in combination. The
fan drive is designed to provide the minimum fan speed (and resulting
fan noise and fuel consumption) required to meet the ever changing
vehicle cooling air flow requirements. You will hear the amount of fan
noise increasing and decreasing as the engine power requirements and
vehicle driving conditions change as you drive. This is to be expected as
being normal to the operation of your vehicle. High levels of fan noise
might also be heard when your engine is first started, and should
normally decrease after driving for a short time.

Driving

11

2010 Econoline

(eco)

Supplement

(supplement)

, 1st Printing

USA

(fus)

«
...
9
10
11
12
13
...
»

Содержание 2010 Econoline









































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Econoline

Бренд: Hama Страницы: 2

Бренд: Abarth Страницы: 36

Бренд: Yakima Страницы: 12

Бренд: JEHNERT SOUND DESIGN Страницы: 8

Experience Series

Бренд: Rainbow Страницы: 19

Бренд: Yakima Страницы: 12

Бренд: Vauxhall Страницы: 323

Бренд: Metra Electronics Страницы: 12

Бренд: Halfords Страницы: 4

Бренд: SAN HIMA Страницы: 7

Peterbilt SmartAir

Бренд: Paccar Страницы: 58

Бренд: Mercedes-Benz Страницы: 153

Бренд: tams elektronik Страницы: 44

Evo All THAR-FOR3

Бренд: Fortin Страницы: 7

Бренд: Meta System Страницы: 22

Бренд: KEKO Страницы: 3

Бренд: Movon Страницы: 43

Бренд: r.LiNK Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды