Ford 2008 mark lt страница 254 Скачать руководство пользователя | Manualshive

Страница: 254 / 328

background image

Stowing the flat/spare tire

Note:

Failure to follow spare tire stowage instructions may result in

failure of cable or loss of spare tire.

1. Lay the tire on the ground with the valve stem facing in the direction
specified on the Tire Changing Instructions located with the jack
hardware.

2. Slide the wheel partially under the vehicle and install the retainer
through the wheel center. Pull on the cable to align the components at
the end of the cable.

3. Turn the jack handle clockwise until the tire is raised to its stowed
position underneath the vehicle. The effort to turn the jack handle
increases significantly and the spare tire carrier ratchets or slips when
the tire is raised to the maximum tightness. Tighten to the best of your
ability, to the point where the ratchet/slip occurs, if possible. The spare
tire carrier will not allow you to overtighten. If the spare tire carrier
ratchets or slips with little effort, take the vehicle to your authorized
dealer for assistance at your earliest convenience.

4. Check that the tire lies flat against the frame and is properly
tightened. Try to push or pull, then turn the tire to be sure it will not
move. Loosen and retighten, if necessary. Failure to properly stow the
spare tire may result in failure of the winch cable and loss of the tire.

5. Repeat this tightness check procedure when servicing the spare tire
pressure (every six months, as per your

scheduled maintenance

information),

or at any time that the spare tire is disturbed through

service of other components.

6. If removed, install the spare tire lock (if equipped) into the bumper
drive tube with the spare tire lock key (if equipped) and jack handle.

WHEEL LUG NUT TORQUE SPECIFICATIONS

Retighten the lug nuts to the specified torque within 100 miles (160 km)
after any wheel disturbance (rotation, flat tire, wheel removal, etc.).

Bolt size

Wheel lug nut torque*

lb.ft.

N

•

m

M14 x 2.0

150

200

* Torque specifications are for nut and bolt threads free of dirt and
rust. Use only Ford recommended replacement fasteners.

2008 Mark LT

(mlt)

Owners Guide (post-2002-fmt)
USA

(fus)

Roadside Emergencies

254

«
...
252
253
254
255
256
...
»

Содержание 2008 mark lt









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 mark lt

Бренд: Acdeos Страницы: 7

Бренд: Ignition Страницы: 1

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Бренд: Yakima Страницы: 8

Бренд: Metra Electronics Страницы: 4

REARSIGHT OnStar 250-8822

Бренд: Rostra Страницы: 2

Бренд: Axxess Страницы: 8

PERFECTVIEW CAM80AHD

Бренд: Dometic Страницы: 196

Бренд: Haibang Страницы: 6

Бренд: Acura Страницы: 2

Бренд: Boyo Страницы: 9

Бренд: SAN HIMA Страницы: 10

TX-STAMP-4-FC04

Бренд: Over Armour Offroad Страницы: 9

Бренд: ECS Страницы: 4

Бренд: Whispbar Страницы: 15

Бренд: Streetwize Страницы: 4

Бренд: Lantronix Страницы: 51

CHALLENGER GK-6125A 2018

Бренд: Coolster Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды